(800) 853-2651
SHOP NOW

Recent content by Walkinfuss

Yesterday's Tractor Forums
  1. W

    MM Jet Star 3 Super

    Thanks guys,
  2. W

    MM Jet Star 3 Super

    Good point, thanks. It does not leak, but if it's a vacuum, then it would not leak oil. I'll dig into that tonight after work. Thanks for the input.
  3. W

    MM Jet Star 3 Super

    Thanks Chris. I found one local. Now I'm looking for the hydraulic oil filter element. Book says OEM # is 10P1851. Crosses to a Wix 51828. The wix 51828 is about 1 taller than the OEM and the O-rings supplied with the filter are way too small, can't stretch to fit the canister...
  4. W

    MM Jet Star 3 Super

    That would be great. Was looking at one off an Oliver, just need to open the I.D. from 2.25" to 2.5" What do you want for it? BTW, the oil pump was perfect, thanks
  5. W

    MM Jet Star 3 Super

    Uggggg... another set back. Rear wheel hub cracked almost all the way from end to end. Glad I found it now, not when the wheel flies off and kills someone. I could use some direction (again) where to find one. The cast part number is 10A 21924. It's on a 68' Jetstar 3 super. As...
  6. W

    MM Jet Star 3 Super

    Thanks for the offer, all is working well..
  7. W

    MM Jet Star 3 Super

    Will do. Didn't think of end play. Someone was in the motor before, the pistons are .040 over and the crank rod journals miced .020 under size. Didn't want to split the tractor, guess I may have to anyway. Thanks again
  8. W

    MM Jet Star 3 Super

    Relief valve and spring are in great shape, Gets worse now... Took off shims to achieve less gap. Started up, still no oil pressure, then completely stops. Distributor rotor not turning took out the pump drive shaft.... a lot of elbow grease to drift the shaft up and out. ... got it out...
  9. W

    MM Jet Star 3 Super

    Thanks, I knew that at one time.... I seem to forget how bad my memory is. On another note, concerning the oil pump spacing between the engine and oil pump surfaces. .002-.004 spacing is the target and can be achieved by shim/gasket thickness combinations. My conundrum is this. When I...
  10. W

    MM Jet Star 3 Super

    Thanks
  11. W

    MM Jet Star 3 Super

    Can use some more help. The original MM volt meter does not work. I replaced it with a new meter, however the new meter will not allow the engine to crank or star when I jump the starter. Tried a second new meter the same. Put the original meter back in and it starts every time, just no...
  12. W

    M&M Jetstar 3 Super

    Thanks, I saw that after I posted... I was able to get a part number off the seal from the other wheel. It turns out to be a National 450446
  13. W

    M&M Jetstar 3 Super

    Great lead, thanks have a cable on the way. Perhaps someone can lead me to where I can pick up a couple front axle seals. The book calls for 10A6828 felt seal (I can find them everywhere) and a felt seal retainer 10A6825? That's the tough one to locate. I would think there would be a one...
  14. W

    M&M Jetstar 3 Super

    Thanks, I'll check it out
  15. W

    M&M Jetstar 3 Super

    Good day again. The help I received on this forum was fantastic. Fired it up yesterday for the first time in 8 years of setting in a field. Trying to locate a tachometer cable. The PN is 10A7523. Is there any other cable that will work? See tons for Massy, Allice, John Deer, Thanks...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top