(800) 853-2651
SHOP NOW

Recent content by wethomas-HT

Yesterday's Tractor Forums
  1. W

    yanmar 3110 head studs/nuts

    Update 350 hours on a wonderful running machine, no issues, runs beautiful, never used a drop of oil. Very lucky to have found this thing
  2. W

    Coldwater Loader installation 3110 D

    The loader is a well built basic loader. Works very well and is strong, you can turn the tractor over with it if your doing stupid things. On the 3110D it does a good job at clearing too, you have to learn how to finesse it regarding stumps, trees etc. Although some would say that the bucket is...
  3. W

    3110D oil pickup tube

    Wanted to follow up with further information, 350 hours on the machine with no issue, what a wonderful little tractor. runs beautiful, I put a coldwater loader on it and it does a solid days work on this little farm I have. Not too bad a clearing and grading either. Very fortunate to have found...
  4. W

    Coldwater Loader installation 3110 D

    yeah no problem Ive been homesteading thirty acres with no hydraulic help whatsoever, built my house barn etc, now im getting a loader. Kinda did it backwards maybe??
  5. W

    3110D oil pickup tube

    I need to further add that if you install the tube as detailed in the manual, you end up with the trough pointing generally down.
  6. W

    3110D oil pickup tube

    The installation information came from the Hoye version of the 3110 shop manual. There is a photo(cant tell you what page at the present), that shows the trough of the oil pickup tube pointing down. I combined this with the fact that every other engine I've built or worked on has the oil pickup...
  7. W

    3110D oil pickup tube

    Just in case someone wants to know, I found a grainy picture in the service manual that shows the trough of the pickup pointing down towards the oil pan. Just as we reasoned out. Pointing it down makes perfect sense. Thanks for the help
  8. W

    Coldwater Loader installation 3110 D

    After further investigation, We have found that the group of four holes on the bottom of the transmission are the same and the bolt groups on the front frame rail are the same. Gotta hand it to the folks at Coldwater, they went above and beyond to help me verify that. Already ordered the...
  9. W

    Coldwater Loader installation 3110 D

    Hello, Im trying to coordinate with the guys at coldwater so I can get a loader built with the brackets already drilled where they attach to the frame on the 3110D He and I have been trading photos. First I sent measurements for my tractor (3110) these measurements covered the front lower...
  10. W

    yanmar 3110 head studs/nuts

    thanks for the help After this eating on me for a few days, I ordered new studs, new nuts and a new gasket. Im going to take the thing apart and re assemble. Then I can get a good nights sleep. I plan on inspecting the block holes with machinist dye to make sure there is no micro cracks. I...
  11. W

    yanmar 3110 head studs/nuts

    Do you guys think I should back it off to 130 Or Dis assemble and re assemble with new gasket Im really not in the habit of messing around with diesel head gaskets, they have to be perfect, so I may have answered my own question. Thanks
  12. W

    3110 head studs/nuts

    Thanks for help Its not the same engine I have Yanmar 3110 / 3t84d engine It doesn't have bolts, all studs and it doesn't have the additional head assist bolts. All studs eight each, one longer, with additional upper thread length than the rest. Your photo does however, show the location of...
  13. W

    3110 head studs/nuts

    During the installation of the head studs on this tractor, noticed that one of the studs were longer than the others. I had assumed that someone replaced it at some time. I just reviewed the parts manual and discovered that there was one long stud used and its position is shown (from the parts...
  14. W

    yanmar 3110 head studs/nuts

    Because of an out of calibration torque wrench, I torqued the head bolts to 160 ft/lb instead of the factory spec of 130. During the install, none of the nuts binded or jumped, everything went smoothly. The out of calibration torque wrench was discovered when I broke a lug nut at 80 ft lbs the...
  15. W

    3110 D External Hydrailic pump drive gear

    Thanks very much for the work you guys do on this site.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top