(800) 853-2651
SHOP NOW

Recent content by willywonka2

Yesterday's Tractor Forums
  1. W

    Re: deutz timing belt

    I have done several of these belt replacements. If the belt broke make sure you pull the valve cover and inspect the push rods and rocker stand bolts. Key things to remember, #1 is at the Flywheel end. if your facing the flywheel the camshaft will be on the right side. They will be a bolt that...
  2. W

    allis chalmers rod length

    You got bills heads done yet?
  3. W

    Aluminun transmission top

    Lookin to locate a aluminum transmission top fo a farmall 560. Any one got any ideas?
  4. W

    Farmall H Trans gear oil

    Pennzoil EP 68. Its thin like water but has the extreme pressure protection. You will have to go to a Pennzoil distributor to get it. Its used in gearboxes with brass or bronze gears and load bearing parts.
  5. W

    motec

    765 963-6628
  6. W

    Is this a MM front pedestal?

    No its a farmall painted green off of a early h or m
  7. W

    MMM

    Hey Mr MMM Whos got the G705? Is it you? Thats a sharp ride!
  8. W

    few more hp

    Uh looks like a tractor pull
  9. W

    D-301 engine HP

    100 plus.
  10. W

    Minnie Mo Road Grader

    Thanks for the reply. I did notice too that the brakes and clutch pedals looked to be UB. it did have a foot clutch.
  11. W

    Minnie Mo Road Grader

    I have a road grader down the road that was built by American Grader out of a Moline. It appears to be an odd duck because of the G chassis and the U sheet metal. I did look at the engine and it also had the 283. Is this a common find? Was it comon for them to cross up the two?
  12. W

    tractor pulls

    Unlimited mods!
  13. W

    855 cummins pistons

    have tried this stunt before. not worth the time and effort. have to make wrist pin bushings and then find the compression height and mill off the top. after that the have to weld up whats left of the combustion bowl and re machine. alot of time envolved and if you cant do the machine work it...
  14. W

    Tallmadge, Ohio pull (SNOW!!)

    hey mr moline where r u from
  15. W

    whos ready for pulling season?

    Tractor aint. I am. Came back from Dekalb and was primed up. redsm is gonna paint it for me so he has it apart.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top