(800) 853-2651
SHOP NOW

Recent content by woopdedo

Yesterday's Tractor Forums
  1. W

    WANTED: New Holland 345D manual with wiring schematics!

    Thank you. Hope their not $400+.
  2. W

    WANTED: New Holland 345D manual with wiring schematics!

    Good morning. I'm in need of a factory service manual for my 1996 345D New Holland. Still trying to figure out why it's not moving after another $500 shifter!! So I could really use a trouble shooting schematic, and hopefully it's not the trans controller.. Any help is appreciated! Thanks
  3. W

    New Holland 345D 2wd

    Good morning guys n gals. I picked up a '96 345D New Holland about 25yrs ago, and after a few, I had to replace the shuttle shifter lever up by the steering wheel. At the time it was $500+, but figured that I wouldn't have to buy another for at least another 30+ with the amount that I would use...
  4. W

    Older Jacobsen Turfcat T422D Dipstick??

    Good morning guys n gals. I picked up an older Turfcat T422D diesel 72" deck, hydrostatic, 2wd mower. Probably paid too much, but it's ALL THERE!! But after spending several dollars at the car wash it doesn't look that abused. But noticed that the little rubber plug on the dipstick slides up...
  5. G

    Dealer for Don

    Chas. A Lissow & Son Case Tractors - Farm Equipment Hilton New York Ph 7
  6. S

    ford 4630 plastic gas cap?

    1992 ford 4630 diesel all purpose tractor...Anyone know of a substitute for the black plastic screw on gas cap that goes on the plastic tank? $47 plus shipping is a bit steep for a gas cap? It screws on probably 4 or 5 complete turns until someone steals it. There might be a another...
  7. C

    1956 ford 650, unknown lever on left side

    I just acquired a Ford 650, On the left side of tractor, near the PTO lever is another little lever, when depressed, moves a long rod that looks to enter the transmission. What does it do?? Someone else asked the same question, but it was never answered, the responses started discussing...
  8. crsutton81

    Got started planting soybeans

    We finally got in a position where we were caught up enough with other tasks and found enough nerves to start planting them today. Some of the neighbors that don't have tobacco started earlier last week. With the cold nights and days coupled with extensive winds and rather dry conditions, I used...
  9. 3

    cat 941 track adjustor help

    Help..piston is stuck in the cylinder . I tried pulling on the front idler with a chain to free it up . That didnt work . I have since compressed the spring and unbolted the assembly from the loader. Any suggestions ? Can I use some heat ? I cant remove the rod from the cylinder because the...
  10. S

    Value of 8N with loader

    New to the forum.... Thinking of buying an 1949 8N that has a Dearborn front loader and a few other attachments such as a blade and box scraper. I'm going to go see it this weekend and was told everything works. If everything does work and the tractor is in fair condition, what is a fair...
  11. D

    farmall300 electrical update

    tested solenoid like Mark an used red MN ....switch was leaving 12v on ing. terminal....i cant believe i wouldnt of heard grinding...i only smelled electrical hot...i ran the tractor 20min...could it of hurt the alt..runnin like that,,,,the starter sure didnt like it..... ring gear...
  12. R

    Find my conversations from 2018

    Can someone please tell me how to go back to my conversations from 2018 concerning “help me identify my MF tractor. “ I am on the site and signed in but can’t find my profile
  13. Charles in Aus.

    Pie time

    The Broad Beans have matured and the possums have left me enough to make Broad Bean ( Fava Beans ) and Ricotta pies . A favourite of mine as a boy , not quite as good as Mum's but near enough .
  14. J

    Truck with automatic jon f

    I have been on a different route past couple of weeks and since our trucks are assigned to the route and not the driver I have been driving a different truck. It is a 2019 International single axle with a Cummins and 10 speed automatic. Rated and licensed for 80,000 lbs. And yes I can gross...
  15. Dennis P

    Harrison, AR pull

    North Arkansas Rusty Wheels will be having a show & pull October 10th at 1:00. Directions or info found on website or Facebook.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top