(800) 853-2651
SHOP NOW

Recent content by wttnlarry

Yesterday's Tractor Forums
  1. W

    MM model Z

    Ill John, We are located in Watertown Wisconsin between Madison and Milwaukee in southern Dodge county. One of the photos should have been of the serial number but I'm sure sn 00613973 is correct. sorry about that. All for now, Larry.
  2. W

    MM model Z

    Ill John, here are 2 photos that might be of interest to you.
  3. W

    MM model Z

    We are located in Wisconsin, Could send photos. How ca I determine how many LPs produced?
  4. W

    MM model Z

    Hello Molinegb, The serial number comes of the right side of the transmission case. How can I determine how many LPs were produced? All for now, Larry.
  5. W

    MM model Z

    Hello John, This tractor will be offered on a on line auction soon. I can let you know and provide you with a link if interested? Where are you located?
  6. W

    MM model Z

    Have a MM model Z (sn 00613973) tractor on propane that I'm trying to sell for a friend. Can't seem to find much info on this tractor. Trying to determine how many Model Z tractors on propane were manufactured, how rare this tractor is? Also what a fair price for the tractor would be? Thanks...
  7. W

    JD 830 pony motor wiring

    Thank you !!
  8. W

    JD 830 pony motor

    Hello Brandon, I have one more problem that I need your help with. It has to do with the three wires that comes from the ignition switch and go to the starter and magneto. One wire goes on the solenoid with the cable from the battery and that is not a problem. Another goes on the solenoid by...
  9. W

    JD 830 pony motor

    Hello Brandon, I ended up cutting a short 3/4" piece of the end of a hammer handle because of it's rounded shape. I split in half and then into 1/4. I shaped it a bit and then wedged it between the clutch cover and the clutch adjusting disc to hold the clutch disc centered. Then it went together...
  10. W

    JD 830 pony motor removal video

    Hello Dan, I am in the process of reassembling the the transmission and clutch housing assembly to the pony motor. What do you need to do in order to get the splines of the clutch shaft to engage with the hub of the clutch disc? Thank You and all for now, Larry.
  11. W

    JD 830 pony motor removal video

    Hello Brandon, I am in the process of reassembling the the transmission and clutch housing assembly to the pony motor. What do you need to do in order to get the splines of the clutch shaft to engage with the hub of the clutch disc? Thank You.
  12. W

    JD 830 pony motor oil leak

    Thank you DaleF for your your insight and your reply. I will consider all the possibilities you mentioned. In my situation I could see the drip drip drip right under where the starter is bolted to the flywheel bell housing when the pony was running at 3500 to 5000 RPMs. So I concluded that it...
  13. W

    JD 830 pony motor removal video

    Good info, thanks Brandon.
  14. W

    JD 830 pony motor removal video

    Very good idea, thank you.
  15. W

    JD 830 pony motor removal video

    Good info, thanks Dan.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top