(800) 853-2651
SHOP NOW

Recent content by Yudt06

Yesterday's Tractor Forums
  1. Y

    Model B Restoration

    I am gearing up to restore my 1948 Model B. Im in need for a parts tractor as my 48 has different rear rims, the hood is beyond repair, the grill is beyond repair, and the sheet metal (tool boxing below the steering column is missing). Im seeing lots of parts tractors that predate mine and are...
  2. Geo-TH,In

    Funny

  3. Y

    Ford NAA Reproduction Carb

    Well said HA!
  4. Y

    Ford NAA Reproduction Carb

    Thanks for the info. I’ll search for a used one to rebuild. The one currently on there is a reproduction
  5. Y

    Ford NAA Reproduction Carb

    I know the original Marvel carb cant be beat but has anyone had any luck with the high end reproduction Carbs? I just ordered one from Steiner because I refuse to buy a cheap reproduction from ebay or Amazon. Its going on an NAA. Anyone have any luck with them please let me know Ryan
    • Yudt06
    • Thread
    • Replies: 7
    • Forum: Ford
  6. Y

    Ford 711 Loader (soundguy)

    Thanks for all the help guys. After close inspection it intact has that nut to tighten down one the valve is in its proper spot. I?ve ordered some new rubber washers to spec and will see if that will seal this elbow once tighten. I?ll keep everyone posted for future reference
  7. Y

    Ford 711 Loader (soundguy)

    Thanks for all the advice guys. I think I?ll replace that elbow with some Teflon tape and call it a day
  8. Y

    Ford 711 Loader (soundguy)

    I have a hydraulic leak from the elbow located at the bottom of the hydraulic cylinder on my Ford 711 Loader. After disassembly it appears there was some type of a rubber O-Ring or Nylon Flat washer that has since worn away hence the leak. For my 711 Guys like Soundguy can anyone guide me to...
    • Yudt06
    • Thread
    • Replies: 8
    • Forum: Ford
  9. Y

    NAA pump relief valve

    Sorry I definitely removed the cylinder safety check valve and ordered same aftermarket. Similar in design but I notice minor differences such as a lack of a ball bearing that sits in the spring
  10. Y

    NAA pump relief valve

    I recently purchased a new hydraulic pump relief valve for my 54 NAA. This one isn?t the same as the original (ball bearing at the base of the spring). Has anyone replaced this valve with an aftermarket? And has anyone had any issues with it ? Thanks
    • Yudt06
    • Thread
    • Replies: 4
    • Forum: Ford
  11. Y

    54 Ford Headlight Wiring

    Awesome thanks
  12. Y

    54 Ford Headlight Wiring

    Getting ready to install new 12v seal beam lights on the tractor. My question is what gage wiring should I use?
    • Yudt06
    • Thread
    • Replies: 2
    • Forum: Ford
  13. Y

    711 Loader Help

    So I got my new 711 hooked up to my NAA. Worked well for a week and now it is slow to raise if it even raises at all. I?m running it off of an original selecter valve from ford. My three point works just fine but when I switch over to loader I have the issues. I also noted if the loader is...
    • Yudt06
    • Thread
    • Replies: 1
    • Forum: Ford
  14. Y

    Ford 711 loader

    Ultradog, now that I think of it. A while back you posted a photo of a hip bracket for a 53 or 54 for the loader that a friend of yours had. I think that?s the one I bought on eBay a while back.
  15. Y

    Ford 711 loader

    Got the loader all hooked up to the 54 NAA. Much to my surprise the cylinder was solid. Couldn?t tell you the last time it functioned. Now off to sandblasting and powder coating
    • Yudt06
    • Thread
    • Replies: 2
    • Forum: Ford
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top