(800) 853-2651
SHOP NOW

Recent content by Zack b

Yesterday's Tractor Forums
  1. Z

    Case dc spark issue

    There is no kill switch on it now. Just a wire with a bare end near the distributor to ground it out so that isn't an issue now lol. And it has Case cast onto the magneto with Case bird logo
  2. Z

    Case dc spark issue

    Ok. Thanks for the info. Soon as I have time I will try that out and see how it works. Thanks again
  3. Z

    Case dc spark issue

    Just picked up a 1953 DC. Was turning it over to check spark before I flushed tank and opened carb and it has little to no spark. With screwdriver in wire the screwdriver had to touch metal then soon as it starts to come off it will spark. Not far enough away to measure. Definetly not enough to...
  4. Z

    To30

    I have a chance to trade for a Ferguson TO 30 with finish mower, rear blade and chains. I have been looking for a tractor for 3000-4000 pound class. Would a tractor like this be somewhat competitive in a tractor pull. Haven't seen one pull personally
  5. Z

    Continental f400a

    I emailed montesequipment and they said my numbers mat ached up to a f163 engine rated at 40.8 hp. It just surprises me because the valves are adjusted and head shaved and pistons are tight an runs good but is lacking on power. I got it just for pulling but even in 4000 pound class it will just...
  6. Z

    Continental f400a

    I have a 1951 Massey Harris 30. Has a continental F400A engine but I am not sure which one it is and not sure if it is original. There is no tag on the engine towards dipstick. Has what I believe to be 418 stamped next to the F400A and the 9-17 cast in next to that and then 149 cast in...
  7. Z

    MH 30 gearing?

    Ok. Think I'll go smaller tires. Thanks for the help
  8. Z

    Farmall h carb

    I could be wrong but I believe there is a o-ring in the bottom jet. The screw part of the jet screws up inside and the o-ring seals to the screw. I have a W4 and mine leaks there and it has a bad o-ring
  9. Z

    MH 30 gearing?

    What are the differences in ratios between the transmission inputs? And is there any way other than counting teeth to tell what I have and what a different transmission has? Thanks
  10. Z

    MH 30 gearing?

    I have a Massey Harris 30 has 13.6x38 tires on it. Only thing I use it for is antique tractor pulls. It is geared too fast for stoneboat. Will stall out within 20 feet. Motor runs good. Have head off and all looks good inside. Was hoping someone would know of a ring and pinion with a lower...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top