(800) 853-2651
SHOP NOW

Recent content by zlarryd

Yesterday's Tractor Forums
  1. Z

    Farmall 560 diesel preheat button going bad

    Thank you for the help.
  2. Z

    Farmall 560 diesel preheat button going bad

    I searched on line for what to get and how to set up the relay but couldn't find anything. Can you refer me to any info on how to do this?
  3. Z

    Farmall 560 diesel preheat button going bad

    My 560 deisel preheat button has gone bad on me several times recently. Never had this happen before but the new buttons I have bought last a few days and then stop working. I first tried cheap buttons that said they were for the preheat. Now have tried a button from a tractor supply company...
  4. Z

    Farmall 560 gas radiator frame removal

    Well I got the suspect part out this morning. Turns out it was a bolt with a special head. I don't have a wrench that could grip it and it was too tight to get anything in to grip it. I ended up drilling down thru the bolt till I could pop it loose.
  5. Z

    Farmall 560 gas radiator frame removal

    Something broke in my steering and to get to the steering assembly I have to remove the radiator and radiator frame. The frame is fastened on with 3 bolts, about 3/4 inch size, and something else in the fourth hole. I looks kind of like a wedge bolt. I can't get it to come loose. There is...
  6. Z

    Farmhand F25 Loader Question

    Thanks, I was just looking on Agco's site at them. I already picked up new seals here in town at Baum Hydraulics, and the old basket looks fine. The Agco site says I have to call to check on availability of the end piece (#7) but the groove pin is in stock near me. I'm going to run down to the...
  7. Z

    Farmhand F25 Loader Question

    The picture is of the end of the inner cylinder pipe. I took off the rubber end seal before I took the picture. The end piece has a smaller diameter pipe attached to it that fits inside the pipe you see and keeps the end piece lined up with the cylinder pipe wall. The drive in pin is just...
  8. Z

    Farmhand F25 Loader Question

    Thanks for the information! Hopefully Agco still carries parts. My pin looks to be a bit worn and I wouldn't mind replacing the end cap too since it looks scratched and seems too loose. Better to try to replace now and not wait to see what may happens when I'm bringing in bales.
  9. Z

    Farmhand F25 Loader Question

    Thanks for confirming that. I have a round hole on the other side of the pipe but no pin there. Due to I think wear the end piece has a lot of play in it. Do you recall if there should be a pin on each side of the pipe? I am concerned that extra play my cause the end price to maybe turn a...
  10. Z

    Farmhand F25 Loader Question

    I pulled out the high lift pistons of the loader to replace the seals. One piston has been replaced with a matching pipe and has a modified end cup at the seal end that slides onto the pipe end and the seal bolts to the end of this piece. The piece is loose on the pipe and appears to have a...
  11. Z

    560 diesel hydraulic pressure relief valve

    Thanks for both replies. The surge problem has been going on for a couple years and sliowly getting worse. Just got the tractor back from the dealer after clutch and ta replacement and piston sleeves replaced, so has clean oil and filter. Sounds like I need to check the pressure releif valve...
  12. Z

    560 diesel hydraulic pressure relief valve

    My hydraulic pump pressure seems to surge when the tractor is running at any speed. Replaced the hose from the pump to the controls as it started to bulge and then blew from the surges. Put a new hose connection on yesterday and the metal pipe at the bottom of the assembly rocks some from the...
  13. Z

    Disc Mower Mounted on 560 Farmall

    I am considering buying a disc mower and wonder if they will work with the Farmall two point hitch system. I have the third point attachment on the tractor, similar to the three point system. But wonder if there is too much movement in the two point lift system to run a disc mower. Haven't...
  14. H

    TA trouble IH 3388

    I,m having trouble with the TA on my IH 3388, when in HI, and taking off ,it will start in low and directly shift to high, it should not do that, I have read that if low goes on the TA it should still operate in high,is that true, it is also slipping in low at times. Are there any adjustments on...
  15. Z

    560 diesel hydraulic noise

    Thanks for that information. Just tried to order a filter and the web site went screwy. Now have to try to find out if the order went or not.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top