1950 JD B runs rough under load

JD2450

New User
Hi all, recently picked up my first 2 cylinder. 1950 John Deere B (gasoline). Not knowing much about them I purchased kind of blind, obviously could do a general mechanical inspection but nothing specific. Been tinkering with it and recently rebuilt the clutch as the plates were chewed up from misadjustment, and the clutch driver was installed on the wrong spline causing a mean shake. Now that that is resolved, i’m having a few more issues I want to ask for some advice on.

Tractor idles fine, hunts every now and then at idle but overall i’d say runs well. When starting in gears 1-3 it runs well. Gears 4-6 (especially 6) the engine seems to almost buck a bit and sounds like it’s running on 1 cylinder until it gets moving decently and then smooths out. I put 2 new Autolite 388s in it because the old ones were pretty black and sooty. Compression read 90psi on cylinder 1 and 80psi on cylinder 2. Adjusted valves with no change. I have a manual and 10psi difference is pushing the limit per the manual, but not sure if that’s causing my issue. Those numbers are engine cold compression with throttle wide open. it does smoke a little bit here and there so i’m sure that low cylinder could use rings at some point in the future. I also removed the carburetor to clean it, everything checked out in there and I adjusted the load and idle jets with no luck.

I also inspected the points and distributor cap. all looks OK - and checked point gap which is within spec. Plug wires are copper core. The governor does seem to be kind of noisy, not sure if that’s effecting anything but I need to look into that regardless unless they typically are a little noisy?

Any help is appreciated. this is a parade / hay ride tractor so it won’t be worked too hard. Just want it to run correctly.
 
This could be a interesting topic. There is a lot of things that could be causing your problem. The compression you gave is low in my opinion, unless it's an all-fuel variant. New/good engines are about 110 psi. When you say governor is noisy, that is concerning, they shouldn't be noisy. Sounds like you may have a weight issue or bearing issue in it. Incorrect throttle linkage adjustment could be another culprit. When you say you cleaned carburetor, did you take it all apart, brass plugs, emulsion tube, etc. out and get ALL the passages clean with a proper drill bit or similar sized wire? The emulsion tube has a few very small hole that have to be CLEAN to run smooth at load.
To add, I have a 48' A that was totally rebuild, new oversized pistons and tons of pulling power, It also bogs down when first starting in 6th gear unless facing downhill!

These are my opinions only and may be subject to being wrong!!:D
 
Last edited:
Hi all, recently picked up my first 2 cylinder. 1950 John Deere B (gasoline). Not knowing much about them I purchased kind of blind, obviously could do a general mechanical inspection but nothing specific. Been tinkering with it and recently rebuilt the clutch as the plates were chewed up from misadjustment, and the clutch driver was installed on the wrong spline causing a mean shake. Now that that is resolved, i’m having a few more issues I want to ask for some advice on.

Tractor idles fine, hunts every now and then at idle but overall i’d say runs well. When starting in gears 1-3 it runs well. Gears 4-6 (especially 6) the engine seems to almost buck a bit and sounds like it’s running on 1 cylinder until it gets moving decently and then smooths out. I put 2 new Autolite 388s in it because the old ones were pretty black and sooty. Compression read 90psi on cylinder 1 and 80psi on cylinder 2. Adjusted valves with no change. I have a manual and 10psi difference is pushing the limit per the manual, but not sure if that’s causing my issue. Those numbers are engine cold compression with throttle wide open. it does smoke a little bit here and there so i’m sure that low cylinder could use rings at some point in the future. I also removed the carburetor to clean it, everything checked out in there and I adjusted the load and idle jets with no luck.

I also inspected the points and distributor cap. all looks OK - and checked point gap which is within spec. Plug wires are copper core. The governor does seem to be kind of noisy, not sure if that’s effecting anything but I need to look into that regardless unless they typically are a little noisy?

Any help is appreciated. this is a parade / hay ride tractor so it won’t be worked too hard. Just want it to run correctly.
That is actually pretty good compression numbers for a 2 cylinder that hasn’t had a change to the head it should run and not skip.

Often if you have a miss like described and have tried hotter plugs already it is in timing and electrical side.

Distributor or mag?

If distributor try a new cap and wires to your plugs

The answer can also be the same for a mag the wico c could cause some headaches I usually just try a different mag but I realize people usually don’t have them just lying around

Checking timing at the mark on the case and flywheel would be good as well since something was off at the other side of the crank who knows
 
thanks all for the input. Checked out the points again and definetly burnt. Just ordered a tune up kit for the ignition from Steiner, hopefully solves that issue. Will post results once received.

Did some more digging in the governor also - haven’t done any inspection yet but found others had similar noise and found the oil feed hole clogged. Could potentially be that as it doesn’t sound like anything wearing but the sound I would describe as non lubricated gears.

Thanks again!
 
thanks all for the input. Checked out the points again and definetly burnt. Just ordered a tune up kit for the ignition from Steiner, hopefully solves that issue. Will post results once received.

Did some more digging in the governor also - haven’t done any inspection yet but found others had similar noise and found the oil feed hole clogged. Could potentially be that as it doesn’t sound like anything wearing but the sound I would describe as non lubricated gears.

Thanks again!
I would check the governor hole too and maybe redo the carb behind all those brass screws. Ron MN
 
received the ignition tune up from Steiner. Replaced points and condenser, ignition rotor, and gapped points to 0.22. Still has the same symptoms. Both plugs I pulled the check and it is definitely running rich. I pulled the carb back off for a cleaning and no change. Then pulled the intake off to see if maybe it was a clogged air intake but also no change. Kind of at a loss here. Any good way to check spark quality under load? I have verified spark is present and looks good turning over with the starter. Only ignition items not changed are coil, plug wires (they looks good and are copper), and distributor cap.
 
What carburetor is on it? Is it the correct one for that tractor? You cleaned it, But did you really clean it? Is the float level correct?
 
Do you have a magneto or a distributor ?
The point gap for a magneto is .015, the point gap for a delco distributor is .022.
You may be cross firing under the distributor cap
Did you change the rotor? Take a spray bottle and wet the cap and wires with the tractor running in the dark.
 
A49deere: DLXT67 is on it, I believe that is the correct carb. The carb is clean, however I did not adjust the float which I will do and report back.

ET: delco distributor and set to .022. I will check for cross firing as well later tonight. I did change the rotor just not the cap.

I also did some digging into the governor linkage. Previous owner has it all out of whack. I ordered a digital RPM gauge which is due to deliver today to check RPM, but by ear with the speed control all the way forward to me sounds like over speed. The rod from the governor arm to the carb with the speed control all the way forward (high idle) was about a hole forward which should be a half hole back. I need to set that adjustment and the speed control arm adjustment since the tractor doesn’t stop when the arm is pulled all the way back. Not sure if this is my issue but could potentially be if the throttle control and governor aren’t working correctly.

will do some adjustments and troubleshooting and report back. appreciate everyone’s help here!
 
A49deere: DLXT67 is on it, I believe that is the correct carb. The carb is clean, however I did not adjust the float which I will do and report back.

ET: delco distributor and set to .022. I will check for cross firing as well later tonight. I did change the rotor just not the cap.

I also did some digging into the governor linkage. Previous owner has it all out of whack. I ordered a digital RPM gauge which is due to deliver today to check RPM, but by ear with the speed control all the way forward to me sounds like over speed. The rod from the governor arm to the carb with the speed control all the way forward (high idle) was about a hole forward which should be a half hole back. I need to set that adjustment and the speed control arm adjustment since the tractor doesn’t stop when the arm is pulled all the way back. Not sure if this is my issue but could potentially be if the throttle control and governor aren’t working correctly.

will do some adjustments and troubleshooting and report back. appreciate everyone’s help here!
Look for a cross fire on the coil as well.
 
A49deere: DLXT67 is on it, I believe that is the correct carb. The carb is clean, however I did not adjust the float which I will do and report back.

ET: delco distributor and set to .022. I will check for cross firing as well later tonight. I did change the rotor just not the cap.

I also did some digging into the governor linkage. Previous owner has it all out of whack. I ordered a digital RPM gauge which is due to deliver today to check RPM, but by ear with the speed control all the way forward to me sounds like over speed. The rod from the governor arm to the carb with the speed control all the way forward (high idle) was about a hole forward which should be a half hole back. I need to set that adjustment and the speed control arm adjustment since the tractor doesn’t stop when the arm is pulled all the way back. Not sure if this is my issue but could potentially be if the throttle control and governor aren’t working correctly.

will do some adjustments and troubleshooting and report back. appreciate everyone’s help here!
There can be a cross fire on the coil also.
 
A49deere: DLXT67 is on it, I believe that is the correct carb. The carb is clean, however I did not adjust the float which I will do and report back.

ET: delco distributor and set to .022. I will check for cross firing as well later tonight. I did change the rotor just not the cap.

I also did some digging into the governor linkage. Previous owner has it all out of whack. I ordered a digital RPM gauge which is due to deliver today to check RPM, but by ear with the speed control all the way forward to me sounds like over speed. The rod from the governor arm to the carb with the speed control all the way forward (high idle) was about a hole forward which should be a half hole back. I need to set that adjustment and the speed control arm adjustment since the tractor doesn’t stop when the arm is pulled all the way back. Not sure if this is my issue but could potentially be if the throttle control and governor aren’t working correctly.

will do some adjustments and troubleshooting and report back. appreciate everyone’s help here!
JD4520 Adjust the throttle rod to the carburetor where the rod just goes in when wide open throttle. Not 1/2 hole back. Wear on all the governor parts will cause it to not idle down that way when wide open. I do that on our pulling tractors and we want open as we can get. Also the throttle stop pin sometimes will be bent and cause a shift one way or another. Clean the plugs as it doesn't take long to foul them out where it won't run right. Lynn
 
There can be a cross fire on the coil also.
just ran it in the dark - no cross fire anywhere that I could see and I checked everything. Also verified spark at night just by cranking and it’s crisp blue spark so don’t think i’m getting weak spark unless it’s only initially under load.

I will get the throttle adjustment dialed in tomorrow and verify float height as well.

Appreciate everyone’s input, will get it figured out. here is a video of what it is doing as well. This was a simple 4th gear driving and you can hear it cutting out once going up a very slight hill.

 
If you still can not get the B running right, couple more thought? Is the advance linkage free in the distributor? Check ignition timing, 25 degrees at 1310 RPM with power timing light? You said the speed control linkage was wacky? You may buy a new speed change spring- B2636R, on top of the governor on the governor arm, a flat, long piece, bolted to the B 272R governor arm. It can really affect engine performance! This piece can loose its flex over the years!
 
My input may not help a lot as I'm no expert either, but I have just brought 2 B's back to life. My first one had the Magneto converted to 12V external coil setup and after replacing the points and a broken rotor button I was able to get it to run. It was running very rich so I had to go into the carburetor a couple of times and cleaned it really well. I did not rebuild it with a lot of new parts but did discover that the float definitely makes a lot of difference on this one. I had it running well at idle, but under load running a short time it flooded pretty badly. I attempted all the usual adjusting and just couldn't get it to stop. Float and needed appeared to work and close when operating manually of the tractor, but I finally decided a new float was needed. I replaced it and after a couple of times adjusting it to the correct height it runs well. I did have to tweak the idle and load needles a few times to get it where I wanted it.

On the second one I had some issues that after reading your description I thought could be similar. My governor was just constantly adjusting and the tractor would not idle well. I cleaned this carburetor a little more thoroughly and with the new float, needle valve and such it was maybe a little better but still erratic idling. I ran some pretty good quality fuel and some more cleaner through it enough to get it warm a few times and it eventually settled down and is now running quite well. It seems that there is a bit of tweaking required to get them just right for the individual tractor. (by the way mine are both DLTX67 also) The 2nd tractor is a slightly later production with the Delco distributor so they are not completely identical tractors.

That sound on your video does sound a little like my 2nd one during one of my adjustment periods that just needed a little more flow on that load side, but mine is pretty sensitive.
 
You can't look at a spark plug wire and see if it's bad. Don't be cheap, put a new set of copper core spark plug wires on it and expect to do that again in 10 years. Under load they leak the spark away if they are old. How old would be a good guess, don't guess just CHANGE THEM NOW. And start a 10 year clock to renew them again. Hard to find copper core spark plug wires today, only way to avoid that issue is to go pertronix coil and ignition module, but the ten year clock can never be dismissed as it applies to carbon core wires too unless they are 8mm silicone as well. The only reason for copper core wires is a weak spark source, ALL these two lungers came with copper core wires as a side note. Running it with a weak number two cylinder has put the hurt on your compression already. Best of luck with it as I can't count the number of times a new set of wires was the only thing mine needed.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top