Still having problems with the TEA 20 zenith 24 t carb/

GSW

Member
When i purchased this tractor,and got it home,it ran like a champ.I got a stupid idea to put a tablespoon of seafoam in the tank.A couple days later ,the tractor was not working right.It was serching,like starved for gas.I could fiddle and adjust the carb,get it idling and working for a half hour,and then it would start skipping and serching.
Its not the governor,for it worked great when i bought it.

I put a new carb kit on it,two washers under the needle,and it ran pretty well...for a day or so,now back to stumbling,skip,poping through carb. I tested the gas flow through the line,it poured out.The other day i seen gas seeping out through the intake gasket of carb,,and was kinda pulsating a tiny bit of gas when the tractor was running,,as though it was flooding. I did install 2 washers under the needle,,can i put three? to lower the float more?
Im to my wits end. Cant understand why this tractor all of a sudden decided to work crappy when i had it a couple days! I put a new needle in,,not much differance,cleaned and blew out all the jets,carb was clean anyway.The darn carb kits gaskets were thinner than the origional.Should i install the origionals?
ok....thats enough to think on . BTW,the new kit came with a different butterfly flap,,mine was very beat out and loose.This one is tight,but not closing all the way,,a very tiny gap around it in the chamber, My old one was round,this new one is kinda oval....i ruined my old one taking it out.
 
Classic signs of a stuck float from what you describe . The Zenith is prone to it , takes hardly a half a mm of misalignment to cause it .
Tap the carb side with wood or plastic , don't be too enthusiastic. This might free it , I've used that trick countless times .
Otherwise, look carefully at the float for a rough edge or seam that might be snagging , or a rough spot in the bowl doing the same .
Failing that , back to dirty fuel and grit stopping the needle from seating . An inline filter should help that .
 
Classic signs of a stuck float from what you describe . The Zenith is prone to it , takes hardly a half a mm of misalignment to cause it .
Tap the carb side with wood or plastic , don't be too enthusiastic. This might free it , I've used that trick countless times .
Otherwise, look carefully at the float for a rough edge or seam that might be snagging , or a rough spot in the bowl doing the same .
Failing that , back to dirty fuel and grit stopping the needle from seating . An inline filter should help that .
Yup. I tap the float. But I still have to adjust it . I never knew these fergies were so troublesome. Well....back to opening tge carb..again! Btw are two washer ok under the needle?
 
I have heard of adding washers as you mention , never had to resort to it myself though .
The Zenith is usually straightforward, a few tweaks might be needed , you seem to have a troublesome one .
Have you really cleaned out the fuel tank and tap?
Another, remote possibility is that there is a pinhole in the float . Check by submerging in hot water , this will heat the air inside a force a stream of bubbles out of any hole , if there is one .
 
I have heard of adding washers as you mention , never had to resort to it myself though .
The Zenith is usually straightforward, a few tweaks might be needed , you seem to have a troublesome one .
Have you really cleaned out the fuel tank and tap?
Another, remote possibility is that there is a pinhole in the float . Check by submerging in hot water , this will heat the air inside a force a stream of bubbles out of any hole , if there is one .
I plan on taking the carb apart again. When I first opened the carb,when I got the tractor and it started acting up afrer a few days..,someone had two washers on the needke,worked when I got it,for a few days,then all thos happened. Like I said before..I did a stupid thing by pouring a tiny bit of seafoam in an inch of gas. Things got bad after that. A good flow of fuel to th
e carb though.
Ill check the fuel thing under the tank.
Thanks.
 
Yup. I tap the float. But I still have to adjust it . I never knew these fergies were so troublesome. Well....back to opening tge carb..again! Btw are two washer ok under the needle?
Wellllllllllllll,my TEA-20 has been on my property since new. ..1950 .
I have never had a Crab problem.
Since 1974 I have installed two new Carb kits...An "OUNCE" of PREVENTION is worth a "POUND" of cure.
Replaced (TWICE) Worn out timing chain,crankshaft sprockets,and camshaft sprockets.
Replaced (Once)Governor assembly.."weights problem"
Replaced CLUTCH ASSEMBLY (Once)
Replaced (Once) all BEARINGS in Distributor drive.
There is proof in the shop that the previous owner had replaced all VALVES in the HEAD.

When my TEA-20 stated to HUNT / SURGE the entire timing chain,sprockets ,Governor assembly had to be replaced.
Bob..

At the end of a 12 inch ratchet,I noticed the ratchet would move 2" between Clockwise and counterclockwise before the rotor would move. The ROTOR DRIVE on my TEA 20 S#182991 was sloppy and the rotor was starting to contact the CONTACT points inside the Distributor CAP. I replaced the BALL Bearing assembly (inside the distributor assembly) and the amount of side movement / slop of the rotor drive is now nothing.

On my second TEA 20 S#251562 the drive TANG on the end of the DISTRIBUTOR shaft was so badly worn it would misfire. I have a TEA-20 FERGUSON made in England with a POSITIVE GROUND /6 Volts. The COIL has three connections, CENTER HIGH VOLTAGE LEAD to DIST., "SW" and "CB". SW.. Connected to 6 VOLTS supplied FROM IGNITION SWITCH and CB connected to CONTACT BREAKER in Distributor. INFO found in an original HARRY FERGUSON SERVICE MANUAL. With engine running/ operating there is 4 volts from "CB" available to contact Breaker in Distributor.
Please note. The DRIVE TANG on the end of the DISTRIBUTOR on all three of my TEA -20's is OFF CENTER. The drive key way on the GEAR DRIVE matting with the CAMSHAFT is also off center.

When my TEA 20 acted up I placed a socket on the head of the "CAP SCREW" that holds the pulley to the CRANKSHAFT . I then turned the crankshaft Clockwise until the rotor (remove distributor cap and view rotor)started to move. I then turned the crankshaft counter clockwise until the rotor started to move and found that the TIMING chain, and both the CAM sprocket and Crank sprocket had to be replaced. Once I opened up the front cover the GOVERNOR assembly also had to be replaced.

I tap the seal lightly to get it started,(seal is approx.. 1/16" into bore) then placed a piece of 2" X 4" wood across the inboard side of the cover and a piece of 5/16" T X 1" wide metal strap across the seal. Inserted a section of 1/2" all thread through the 5/16"T X 1" wide metal strap and the 2" X 4" wood, with washer and nut on either side pulled the seal in.
A fine film of BLUE SILCONE sealer was applied to the BORE of the Timing cover. As you pull the seal in if the seal appears to be cocked you can lightly tap the seal peripheral and it shall align itself.


Info I compiled when REPLACING Crank sprocket ,Cam sprocket and Timing Chain.
(1) 85 MM Bore Engine:

(2) Front Lip Oil Seal "National /Federal Mogul Lip Seal" # 472164V A SMALL amount of BLUE Silicone was placed around the inside bore of the front timing chain cover before Lip seal was installed:

(3) I installed a repair SLEEVE on the front drive Pulley, make "DURA SLEEVE" # 99175. The sealing area were the LIP SEAL makes contact was slightly grooved. Dura Sleeve specs. 1.745">1.753" Diam. # 68 Rockwell Hardness:

(4) On installation the Governor plunger shall be reseeded tight against the Flyweights and no weights shall be loose or hanging down:

(5) A small amount (only enough to make the surface shiny) of engine oil was added to the shaft of the governor PLUNGER as well as the timing chain:

(6)There are NO timing MARKS on the NEW Sprockets. You may wish to line the timing marks up (facing each other) before you remove the sprockets:

(7)Place the old sprocket (CAM SPROCKET) on top of the new sprockets and accurately scribe the new sprockets as to the timing marks. There are FOUR holes in the hub of the CAM SPROCKET. Keep turning the old sprocket until the four holes and all teeth line up. These holes are slightly off set. I used several SHOULDERED cap screws to ensure I had the new and old sprockets properly aligned. You may have to flip the old sprocket over...see right up:

(8) It's good practice to measure the thickness of the hub of the old crankshaft sprocket and the new crankshaft sprocket as the teeth on the two sprockets should align for both proper operation and longevity.(there were shims between the old Crankshaft sprocket and the shoulder portion of the crankshaft):

Cheers
Bob...

Please consider typing "TEA20 Back to life" in archives of this forum under the FERGUSON section and read all comments from "Griz/Bob (Aust)John(UK) and Tucker101
These gentleman seem to have a great handle on the TEA-20's There are several gentleman from the UK,Ireland,Australia and the USA with more experience than I have...:)
 

Attachments

  • cvphoto37.jpg
    cvphoto37.jpg
    69.3 KB · Views: 0
  • DSCN9703.JPG
    DSCN9703.JPG
    1.8 MB · Views: 0
  • DSCN9704.JPG
    DSCN9704.JPG
    1.8 MB · Views: 0
  • DSCN9705.JPG
    DSCN9705.JPG
    1.9 MB · Views: 0
  • DSCN9706.JPG
    DSCN9706.JPG
    1.9 MB · Views: 0
  • DSCN9708.JPG
    DSCN9708.JPG
    1.8 MB · Views: 0
  • DSCN9709.JPG
    DSCN9709.JPG
    1.1 MB · Views: 0
  • DSCN9711.JPG
    DSCN9711.JPG
    1 MB · Views: 0
  • DSCN9712.JPG
    DSCN9712.JPG
    1.1 MB · Views: 0
Well
I thank you for the info. I checked my points yesterday. The shaft as a very small amount of play....new points though
I adjusted the carb,,a bugger to get right....abd got it to work pretty darn good.
Took it in the woods over cradle hills,wasn't too bad.
Today..I started it up,no choke,then gave it a little choke. It flooded. Waited a bit no choke,and it sputtered to life.
I left it warm up...had to adjust the carb again!!
I got it working very good again.
Now..tomorriw it will need adjustment again properly.
It will run excellent all day. Till the next day,then you have to adjust the carb.
Im not saying it dosnt need some other work.. but I think the float I s sticking.
Its a hateful tractir!
Im tearing the carb apart,and gently sanding the float chamber,just to get tge roughness off. ...I'll let you know if it starts abmnd runs well again.
Funny. Tge guy that had it rant and used it. It ticked lije a clo k fir me,for about threevdays..till I put a little seafoam in the tank...next day my troubles began.
If it dont run well next time,im going to clean out the thing under t he tank.
 
Ok. Will do.
I started the old tea 20 today,started without choke,but it wasn't cold outside. Just one click.
It ran rough for about 5 min,then started clearing up,abd ran pretty darn good. I drove up through whe woods ,and it never stumbled. Idles down to almost nothing and dosnt stall.
Im going to accept that its cold blooded,and go with that,,till colder weather. Things may go south then.
 
If temperature is a consideration try looking at the rocker cover breather valve. It should be clear and have a simple jiggle pin in it to keep the small orifice open .
 

Attachments

  • Air breather valve.JPG
    Air breather valve.JPG
    58.4 KB · Views: 0
  • Like
Reactions: GSW
Well
I thank you for the info. I checked my points yesterday. The shaft as a very small amount of play....new points though
I adjusted the carb,,a bugger to get right....abd got it to work pretty darn good.
Took it in the woods over cradle hills,wasn't too bad.
Today..I started it up,no choke,then gave it a little choke. It flooded. Waited a bit no choke,and it sputtered to life.
I left it warm up...had to adjust the carb again!!
I got it working very good again.
Now..tomorriw it will need adjustment again properly.
It will run excellent all day. Till the next day,then you have to adjust the carb.
Im not saying it dosnt need some other work.. but I think the float I s sticking.
Its a hateful tractir!
Im tearing the carb apart,and gently sanding the float chamber,just to get tge roughness off. ...I'll let you know if it starts abmnd runs well again.
Funny. Tge guy that had it rant and used it. It ticked lije a clo k fir me,for about threevdays..till I put a little seafoam in the tank...next day my troubles began.
If it dont run well next time,im going to clean out the thing under t he tank.
"thing under the tank" That is the sediment bowl. It separates water from gasoline and catches fine debris. Look closely and it is contains any water, you can see the separation line between gas and water. When the bowl is removed, look up into the casting, there should be a fine mesh plastic screen, which is removable for cleaning. When the sediment bowl casting is removed from the gas tank, you'll find a brass screen covering the opening to allow gas to flow. It's top is open JIC the screen stops up with gunk and coarse sediment.
Be prepared to catch any remaining gas in the tank that could not be drained by removing the sediment bowl, and opening the petcock.
1793270422695.png
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top