Whitte hit-and-miss engine

m16ty

Member
I got this Whitte 4 hp about a year ago. Since then all I’ve done is free everything up from sitting. It seems to have good compression and I want to see if I can get it running. Bought a model T buzz coil that was DOA, so I decided to build me one from a video on YouTube. I’m getting good spark from my coil so what is next?

I know next to nothing about these old engines, other than just seeing them run at shows.i don’t even know how to start it if i do get good spark and fuel. I’ve tried to just turn it over by hand but when I hit the compression stroke it just stops. Are there any good videos out there that show the basics of starting and running one of these things?
 

Attachments

  • IMG_2838.jpeg
    IMG_2838.jpeg
    2.1 MB · Views: 0
  • IMG_3455.jpeg
    IMG_3455.jpeg
    2.5 MB · Views: 0
I got this Whitte 4 hp about a year ago. Since then all I’ve done is free everything up from sitting. It seems to have good compression and I want to see if I can get it running. Bought a model T buzz coil that was DOA, so I decided to build me one from a video on YouTube. I’m getting good spark from my coil so what is next?

I know next to nothing about these old engines, other than just seeing them run at shows.i don’t even know how to start it if i do get good spark and fuel. I’ve tried to just turn it over by hand but when I hit the compression stroke it just stops. Are there any good videos out there that show the basics of starting and running one of these things?
When you say it just stops, can you not turn it anymore?
It has to go on to top dead center where it fires to ignite the gas fuel mixture.
 
When you say it just stops, can you not turn it anymore?
It has to go on to top dead center where it fires to ignite the gas fuel mixture.
I can turn it slow through the compression stroke (letting compression bleed off as a turn it) but trying to turn it fast I’m not strong enough to turn the flywheel through the compression stroke. It will just kick back on me. Or I can hold one of the valves open and turn it through. It’s not binding or anything, it’s just got so much compression.
 
I can turn it slow through the compression stroke (letting compression bleed off as a turn it) but trying to turn it fast I’m not strong enough to turn the flywheel through the compression stroke. It will just kick back on me. Or I can hold one of the valves open and turn it through. It’s not binding or anything, it’s just got so much compression.
Once you get spark and fuel set correctly, it will crank by pulling it over compression even very slowly.
If it kicks back, then it is firing a bit too early.
Just keep your fingers out of the spokes in the flywheel.
 
I can turn it slow through the compression stroke (letting compression bleed off as a turn it) but trying to turn it fast I’m not strong enough to turn the flywheel through the compression stroke. It will just kick back on me. Or I can hold one of the valves open and turn it through. It’s not binding or anything, it’s just got so much compression.
That's how you start most. Hold the valve open,turn flywheels to build up momentum, let go of the valve and let the weight of the flywheels carry it through the compression stroke.
 
You have to run it right side up or all the water will come out.
 

Attachments

  • IMG_6471.jpeg
    IMG_6471.jpeg
    221.7 KB · Views: 0
  • Haha
Reactions: JWA
Most of these engines have a pet-cock that you can open to prime the engine. When starting leave pet-cock open to allow some compression to escape making it easier to start. After it starts close pet-cock but be careful as when it fires it can burn you.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top