Diesel Gypsy
Member
My new-to-me Ford 641 Workmaster doesn't want to run and I'm running out of ideas on what is wrong.
PO #1 had put new points and condenser and a new carb on it and was supposedly driving it into town to get some gas in it. On the way it stalled and he couldn't get it going again so he sold it to PO #2.
PO #2 got it running but badly. Before he was able to do more he got sick and eventually passed away.
3 years later PO #2's son sold it to me and all the previous info is from his memory of the story so far.
I got it running badly much like PO #2 had probably done. It was flooding, misfiring and backfiring and barely running. So I took the carb off and cleaned out the old gas residue from 3 years sitting. Re-installed carb but same result. Next I checked the points which looked excellent although they were gapped way too wide so I adjusted them but the same result. Next I checked the timing which was much advanced so I set it back to 8*. Same result. But here is my first clue that I am repeating the PO's work, the timing mark door was already open and the 8* mark was clearly marked with yellow paint marker! Hmmm!
So the next step was a compression test. So they were (1-4) 145, 130, 135, 150. Not quite as close as I'd like but it certainly should run!
I've had the carb apart twice more to make sure everything was clear and the float was working properly and it all seems perfect. I also drained all the old gas and replaced with new. New plugs and made sure all were firing so the wiring seems fine.
So what am I missing????
The only other thing I can think of is the valve timing being out but I don't know how that could happen with gear drive, although I don't know the history of what has been done to it other than what I was told. The engine is pretty clean so it may have been apart, could it have been put together out of time? I'm stretching here but I can't think what else could be wrong!
I would really appreciate some other ideas from some of you who know these engines better than me!
Jim
PO #1 had put new points and condenser and a new carb on it and was supposedly driving it into town to get some gas in it. On the way it stalled and he couldn't get it going again so he sold it to PO #2.
PO #2 got it running but badly. Before he was able to do more he got sick and eventually passed away.
3 years later PO #2's son sold it to me and all the previous info is from his memory of the story so far.
I got it running badly much like PO #2 had probably done. It was flooding, misfiring and backfiring and barely running. So I took the carb off and cleaned out the old gas residue from 3 years sitting. Re-installed carb but same result. Next I checked the points which looked excellent although they were gapped way too wide so I adjusted them but the same result. Next I checked the timing which was much advanced so I set it back to 8*. Same result. But here is my first clue that I am repeating the PO's work, the timing mark door was already open and the 8* mark was clearly marked with yellow paint marker! Hmmm!
So the next step was a compression test. So they were (1-4) 145, 130, 135, 150. Not quite as close as I'd like but it certainly should run!
I've had the carb apart twice more to make sure everything was clear and the float was working properly and it all seems perfect. I also drained all the old gas and replaced with new. New plugs and made sure all were firing so the wiring seems fine.
So what am I missing????
The only other thing I can think of is the valve timing being out but I don't know how that could happen with gear drive, although I don't know the history of what has been done to it other than what I was told. The engine is pretty clean so it may have been apart, could it have been put together out of time? I'm stretching here but I can't think what else could be wrong!
I would really appreciate some other ideas from some of you who know these engines better than me!
Jim