Ford 641 won't run! Need Ideas!

I know that most of you have been thinking it's an ignition problem but everything checks out perfectly on that end. I have a nice bright spark on all plugs, so I am leaning more to a carburetor problem.

This carb is a TSX 785 and appears to be a new replacement but I don't know if it has ever run properly on this carb. I don't have the original carb and I don't know why it would have been changed. I have had this carb apart several times and I can't find any fault with it but I still don't have a running tractor! 🤬

With that in mind, I ordered a new carb off Amazon. This one is a TSX 765 and is supposed to be the right one. It has the fuel inlet on the end just below the main adjustable jet knob and the mounting bolts are 2.38" apart. This is all the same as the carb on it now but the tag number is different so I don't know what the difference would be. Does anyone know?
 
I don't think the clip would make any difference, the rotor fits VERY snug on the shaft so I'm quite sure it isn't moving at all.
I wonder if it is the right rotor. Check to see that that flat that goes on the shaft matches the location in relationship to the one in the picture below. I will not say company has not made a rotor that doesn't need the clip to align the rotor button, but I have not encountered one. I suppose it is possible you have an after market distributor. Not ruling anything out. Can you post pictures of your complete distributor and one with the cap off showing the points and condenser?

C0NN12200A rotor button.jpg
 
to find out if it is a lack of gas, take a spray bottle and keep spraying gas in the carb and see if you can make it run like that. I have never seen an engine with good spark and compression not run well while spraying the right amount of gas in the carb. This will tell you if it gas related. I have even disconnected the gas line so It can not flood as well. If the wrong carb it can do what you say.
 
Ok… Here is a process I have used repeatedly. It works great on systems like the 641. You already have the intake hose off. Using an old spray bottle with good gas in it, spray a few squirts into the carb. Immediately try to start. If it starts, if fuel supply/carb is the issue, you can likely keep it running with a few intermittent squirts into the intake. If it doesn’t stay running on a squirt bottle, you likely have an ignition issue.

And here is one big advantage of this process… If the carb (jetting, plugging, etc.) is the issue, having the engine run on a spray bottle for a bit, with often clear up carb issues. I think the vacuum, heat, vibration will often help clean out the carb.

Good luck.
 
to find out if it is a lack of gas, take a spray bottle and keep spraying gas in the carb and see if you can make it run like that. I have never seen an engine with good spark and compression not run well while spraying the right amount of gas in the carb. This will tell you if it gas related. I have even disconnected the gas line so It can not flood as well. If the wrong carb it can do what you say.
Sorry to dupe your answer! I took to long!
 
My new-to-me Ford 641 Workmaster doesn't want to run and I'm running out of ideas on what is wrong.

PO #1 had put new points and condenser and a new carb on it and was supposedly driving it into town to get some gas in it. On the way it stalled and he couldn't get it going again so he sold it to PO #2.

PO #2 got it running but badly. Before he was able to do more he got sick and eventually passed away.

3 years later PO #2's son sold it to me and all the previous info is from his memory of the story so far.

I got it running badly much like PO #2 had probably done. It was flooding, misfiring and backfiring and barely running. So I took the carb off and cleaned out the old gas residue from 3 years sitting. Re-installed carb but same result. Next I checked the points which looked excellent although they were gapped way too wide so I adjusted them but the same result. Next I checked the timing which was much advanced so I set it back to 8*. Same result. But here is my first clue that I am repeating the PO's work, the timing mark door was already open and the 8* mark was clearly marked with yellow paint marker! Hmmm!

So the next step was a compression test. So they were (1-4) 145, 130, 135, 150. Not quite as close as I'd like but it certainly should run!

I've had the carb apart twice more to make sure everything was clear and the float was working properly and it all seems perfect. I also drained all the old gas and replaced with new. New plugs and made sure all were firing so the wiring seems fine.

So what am I missing????

The only other thing I can think of is the valve timing being out but I don't know how that could happen with gear drive, although I don't know the history of what has been done to it other than what I was told. The engine is pretty clean so it may have been apart, could it have been put together out of time? I'm stretching here but I can't think what else could be wrong!

I would really appreciate some other ideas from some of you who know these engines better than me!

Jim
To make an engine run you need compression --- fuel --- and spark at the correct time to the correct cylinder. You have compression ---You can make sure it is or is not a fuel problem with a can of starting fluid even with the carburetor off as well as with it on. spark at the correct time can be correct and still have spark at the fuel in the cylinder. After reading all the good suggestions my guess you might have a spark plug problem.
New plugs does not count!

I had just assembled an Allis B for a tractor pull. when I started to pull it began to miss. I had bought a pull in the next weight class. I took the tractor to the truck and pulled one plug wire of at a time to find which cylinder gave up. I put two used plugs from the tool box in, added weight and went back and took third place without a miss. Just a thought. Back firing is normally spark at the wrong time in the wrong place.
If it will run crappy I would take one plug wire off at a time and if it does not change the sound just leave it off. If you have two only that does not changeany thing then switch those wires ton see what happens.
 
Hi Diesel Gypsy,
In the first post you said
" Next I checked the timing which was much advanced so I set it back to 8*. Same result. But here is my first clue that I am repeating the PO's work, the timing mark door was already open and the 8* mark was clearly marked with yellow paint marker! Hmmm!"

Are you putting the flywheel at the 8° mark to set static timing?
Its 4° here
13110.jpg

13183.jpg
 
Backfiring through the carb its chasing fuel(vapor), out the exhaust its chasing liquid gas. I am guessing your sediment bowl valve, and, or steel fuel line are gunked up.
 
Hi Diesel Gypsy,
In the first post you said
" Next I checked the timing which was much advanced so I set it back to 8*. Same result. But here is my first clue that I am repeating the PO's work, the timing mark door was already open and the 8* mark was clearly marked with yellow paint marker! Hmmm!"

Are you putting the flywheel at the 8° mark to set static timing?
Its 4° here
View attachment 168617
View attachment 168615
The simple setting timing that was shown to me in the 1950's. Of course thereis more than one way to correctly to shin a cat. However you can time any engine by setting number one piston at top dead center on the flywheel and remember top dead center comes into view twice, (Once top dead center an0d the second time the piston is at bottom dead center) Dumb wrong statement! So make sure when you read the flywheel that the piston is up. at that point the points should be just ready to open. you rotate the distributer back and forth to make sure I check with the switch on to see the spark. The rotor then must point toward the number one plug wire. When the engine starts to start the mechanical advance will let your 4 degrees show to a timing light on the flywheel. Many people get confused with the advance degrees in the tec sheets.
I say go back to the old basics to avoid confusion.
It might start on two cylinders looking at the flywheel for top dead center with top dead center on the wrong piston,I am not sure.
 
Last edited:
Backfiring through the carb its chasing fuel(vapor), out the exhaust its chasing liquid gas. I am guessing your sediment bowl valve, and, or steel fuel line are gunked up.
My bet also goes with lack of fuel. In an early reply you said “has good fuel flow” where did you check this? In my opinion you have to check it at the carb bowl drain. And you can’t just pull the plug and immediately say yep it is good, you have to wait 5-10 seconds for the carb bowl to empty.
This may not be it but we need this answer before we can agree that your fuel flow is good.
 
My bet also goes with lack of fuel. In an early reply you said “has good fuel flow” where did you check this? In my opinion you have to check it at the carb bowl drain. And you can’t just pull the plug and immediately say yep it is good, you have to wait 5-10 seconds for the carb bowl to empty.
This may not be it but we need this answer before we can agree that your fuel flow is good.
I pulled the line off at the inlet to the carb (after the filter and sediment bowl) and there was plenty of fuel. I also hooked it back up and checked that fuel flowed freely through the float valve by pulling the bowl drain plug. Again, plenty of fuel flow.

Today I tried it again and was able to get it 'running' for about 2 minutes. It ran on all cylinders but could only run at a max of 450 rpm (the tach works! :D). Opening the throttle to speed it up just caused it to run very ragged and labored with no increase in speed. Seemed like it was starving for fuel but adding some choke just caused it to die. Also adjusting the needles was how I got it to run at all and the best it got was about 400/450 rpm.

I seriously think there is something wrong in the carb that I have missed or possibly its the wrong carb? although the one I ordered looks exactly the same but . . .
 
I am now thinking it is in the distributor. A stuck advance can make it act like that. I had the carburetor on an Oliver 1850 apart three times thinking I had missed something. I had been talking to the Oliver dealer having the same thought. He said go out and take the distributor out of your 1650 and try that. I did and it worked. The problem was the mechanical advance had rusted and stuck while I was fitting ground and would only fast idle and wouldn't pull a load. When you tried to speed it up it would sputter and die. It would start right back up at fast idle.
All 40 of my tractors set out year around. I have had two other tractors have advance weights stick since. Clean them up and they work fine.
On the 1850 the bottom bushing needed replaced when I took it out.
 
I am now thinking it is in the distributor. A stuck advance can make it act like that. I had the carburetor on an Oliver 1850 apart three times thinking I had missed something. I had been talking to the Oliver dealer having the same thought. He said go out and take the distributor out of your 1650 and try that. I did and it worked. The problem was the mechanical advance had rusted and stuck while I was fitting ground and would only fast idle and wouldn't pull a load. When you tried to speed it up it would sputter and die. It would start right back up at fast idle.
All 40 of my tractors set out year around. I have had two other tractors have advance weights stick since. Clean them up and they work fine.
On the 1850 the bottom bushing needed replaced when I took it out.
That's a good thought. I'll check that out tomorrow!

40 tractors? Wow!
 
I am now thinking it is in the distributor. A stuck advance can make it act like that. I had the carburetor on an Oliver 1850 apart three times thinking I had missed something. I had been talking to the Oliver dealer having the same thought. He said go out and take the distributor out of your 1650 and try that. I did and it worked. The problem was the mechanical advance had rusted and stuck while I was fitting ground and would only fast idle and wouldn't pull a load. When you tried to speed it up it would sputter and die. It would start right back up at fast idle.
All 40 of my tractors set out year around. I have had two other tractors have advance weights stick since. Clean them up and they work fine.
On the 1850 the bottom bushing needed replaced when I took it out.
why would it die at idle if that was the problem?
 
The simple setting timing that was shown to me in the 1950's. Of course thereis more than one way to correctly to shin a cat. However you can time any engine by setting number one piston at top dead center on the flywheel and remember top dead center comes into view twice. Once top dead center and the second time the piston is at bottom dead center. So make sure when you read the flywheel that the piston is up. at that point the points should be just ready to open. you rotate the distributer back and forth to make sure I check with the switch on to see the spark. The rotor then must point toward the number one plug wire. When the engine starts to start the mechanical advance will let your 4 degrees show to a timing light on the flywheel. Many people get confused with the advance degrees in the tec sheets.
I say go back to the old basics to avoid confusion.
It might start on two cylinders looking at the flywheel for top dead center with top dead center on the wrong piston,I am not sure.
Psssst, better edit that,it's actually at top both times. Wouldn't want folks to think you are starting to get old,feeble and having brain farts. 🤭
 
I pulled the line off at the inlet to the carb (after the filter and sediment bowl) and there was plenty of fuel. I also hooked it back up and checked that fuel flowed freely through the float valve by pulling the bowl drain plug. Again, plenty of fuel flow.

Today I tried it again and was able to get it 'running' for about 2 minutes. It ran on all cylinders but could only run at a max of 450 rpm (the tach works! :D). Opening the throttle to speed it up just caused it to run very ragged and labored with no increase in speed. Seemed like it was starving for fuel but adding some choke just caused it to die. Also adjusting the needles was how I got it to run at all and the best it got was about 400/450 rpm.

I seriously think there is something wrong in the carb that I have missed or possibly its the wrong carb? although the one I ordered looks exactly the same but . . .
What happens when you spray some fuel into the carb?
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top