Ford 641 won't run! Need Ideas!

The simple setting timing that was shown to me in the 1950's. Of course thereis more than one way to correctly to shin a cat. However you can time any engine by setting number one piston at top dead center on the flywheel and remember top dead center comes into view twice. Once top dead center and the second time the piston is at bottom dead center. So make sure when you read the flywheel that the piston is up. at that point the points should be just ready to open. you rotate the distributer back and forth to make sure I check with the switch on to see the spark. The rotor then must point toward the number one plug wire. When the engine starts to start the mechanical advance will let your 4 degrees show to a timing light on the flywheel. Many people get confused with the advance degrees in the tec sheets.
I say go back to the old basics to avoid confusion.
It might start on two cylinders looking at the flywheel for top dead center with top dead center on the wrong piston,I am not sure.
Better rethink that. The piston will be at top dead center any time the timing mark is in line for tdc. Meaning the piston will be up no matter which revolution it is on. It may be on the exhaust stroke, but the piston will still be at the top of its travel, never at the bottom.

Missed reply #39...sorry to repeat the same!
 
Last edited:
I'm always a little skeptical when people say they have plenty of fuel flow without explaining how they determined the flow. I'd recommend...
1. turn off the gas valve.
2. Disconnect the fuel line at the carburetor.
3. Remove the carb drain plug and let it drain until it stops.
4. Reconnect the fuel line.
5. Open the fuel valve, leaving the drain plug out of the carburetor.
6. Measure how much fuel flows out of the drain over the course of 2 minutes, and observe if the fuel flow starts fast and tapers to a trickle the longer it flows.
Just my $0.02.
 
My new-to-me Ford 641 Workmaster doesn't want to run and I'm running out of ideas on what is wrong.

PO #1 had put new points and condenser and a new carb on it and was supposedly driving it into town to get some gas in it. On the way it stalled and he couldn't get it going again so he sold it to PO #2.

PO #2 got it running but badly. Before he was able to do more he got sick and eventually passed away.

3 years later PO #2's son sold it to me and all the previous info is from his memory of the story so far.

I got it running badly much like PO #2 had probably done. It was flooding, misfiring and backfiring and barely running. So I took the carb off and cleaned out the old gas residue from 3 years sitting. Re-installed carb but same result. Next I checked the points which looked excellent although they were gapped way too wide so I adjusted them but the same result. Next I checked the timing which was much advanced so I set it back to 8*. Same result. But here is my first clue that I am repeating the PO's work, the timing mark door was already open and the 8* mark was clearly marked with yellow paint marker! Hmmm!

So the next step was a compression test. So they were (1-4) 145, 130, 135, 150. Not quite as close as I'd like but it certainly should run!

I've had the carb apart twice more to make sure everything was clear and the float was working properly and it all seems perfect. I also drained all the old gas and replaced with new. New plugs and made sure all were firing so the wiring seems fine.

So what am I missing????

The only other thing I can think of is the valve timing being out but I don't know how that could happen with gear drive, although I don't know the history of what has been done to it other than what I was told. The engine is pretty clean so it may have been apart, could it have been put together out of time? I'm stretching here but I can't think what else could be wrong!

I would really appreciate some other ideas from some of you who know these engines better than me!

J

My new-to-me Ford 641 Workmaster doesn't want to run and I'm running out of ideas on what is wrong.

PO #1 had put new points and condenser and a new carb on it and was supposedly driving it into town to get some gas in it. On the way it stalled and he couldn't get it going again so he sold it to PO #2.

PO #2 got it running but badly. Before he was able to do more he got sick and eventually passed away.

3 years later PO #2's son sold it to me and all the previous info is from his memory of the story so far.

I got it running badly much like PO #2 had probably done. It was flooding, misfiring and backfiring and barely running. So I took the carb off and cleaned out the old gas residue from 3 years sitting. Re-installed carb but same result. Next I checked the points which looked excellent although they were gapped way too wide so I adjusted them but the same result. Next I checked the timing which was much advanced so I set it back to 8*. Same result. But here is my first clue that I am repeating the PO's work, the timing mark door was already open and the 8* mark was clearly marked with yellow paint marker! Hmmm!

So the next step was a compression test. So they were (1-4) 145, 130, 135, 150. Not quite as close as I'd like but it certainly should run!

I've had the carb apart twice more to make sure everything was clear and the float was working properly and it all seems perfect. I also drained all the old gas and replaced with new. New plugs and made sure all were firing so the wiring seems fine.

So what am I missing????

The only other thing I can think of is the valve timing being out but I don't know how that could happen with gear drive, although I don't know the history of what has been done to it other than what I was told. The engine is pretty clean so it may have been apart, could it have been put together out of time? I'm stretching here but I can't think what else could be wrong!

I would really appreciate some other ideas from some of you who know these engines better than me!

Jim
the plate in the distributer that the points are screwed to is your mechanical advance for timing. in my 860 i found that under the plate was packed solid and not allowing the plate to either advance or retard. while this may now help your issue, it may be worth your time to take a look to make sure the plate moves. my tractor sat for quite a few years as well. the area was plugged solid. good luck
 
why would it die at idle if that was the problem?
I might have miss read or miss understood but I thought it was running at idle and died when he tried to speed it up in the last post I read. If I was wrong I am sorry.
 
Better rethink that. The piston will be at top dead center any time the timing mark is in line for tdc. Meaning the piston will be up no matter which revolution it is on. It may be on the exhaust stroke, but the piston will still be at the top of its travel, never at the bottom.

Missed reply #39...sorry to repeat the same!
Your correct I had a brainfart. the TDC comes up twice and then once on compression and once on exhaust.
When I was buying dead tractors before 20 years ago I put my thumb over the number one plug hole to feel compression to find the correct TDC. If I did not feel anything after turning it over a few times the valve cover came off without hesitation so I could see both valves were closed when the flywheel showed TDC. In the last 50 years I have never ask for help. I never took a tractor to someone's shop and util my factory became 24 seven I never took a car or truck to someone's shop. I have rebuilt engines since being in my 20's
Thanks, I do appreciate you calling out my dumb mistake. I don't know where it came from there is no excuse for that dumb of a statement.
 
That's a good thought. I'll check that out tomorrow!

40 tractors? Wow!
Come and see. Most of them are not running anymore. Some are at the factory and some are in my back yard. Only the two 5020's I can figure out how to get on. Most of my outside pictures show tractors in the back ground. It was a runaway hobby buying dead tractors up to 1500 miles away. Some at home and one 1500 miles away being loaded for your enjoyment.
1793633593041.png
1793633739163.png
 
Your correct I had a brainfart. the TDC comes up twice and then once on compression and once on exhaust.
When I was buying dead tractors before 20 years ago I put my thumb over the number one plug hole to feel compression to find the correct TDC. If I did not feel anything after turning it over a few times the valve cover came off without hesitation so I could see both valves were closed when the flywheel showed TDC. In the last 50 years I have never ask for help. I never took a tractor to someone's shop and util my factory became 24 seven I never took a car or truck to someone's shop. I have rebuilt engines since being in my 20's
Thanks, I do appreciate you calling out my dumb mistake. I don't know where it came from there is no excuse for that dumb of a statement.
I wouldn't say dumb by any means. Like you said, brain fart! It happens to me all the time. I get an idea in my head and run with it without thinking it through. Then I have a "wait a minute" moment and wonder why I was thinking what I was thinking!
 
Come and see. Most of them are not running anymore. Some are at the factory and some are in my back yard. Only the two 5020's I can figure out how to get on. Most of my outside pictures show tractors in the back ground. It was a runaway hobby buying dead tractors up to 1500 miles away. Some at home and one 1500 miles away being loaded for your enjoyment.
View attachment 168657View attachment 168658
I'm thinking somebody should posts more pictures........
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top