M602 found in a barn on the property unknown condition

AlbersBB10

New User
13523.jpg
I found a tractor and have never been around tractors. From the city and married a country girl. What doi need to do to her? It has a battery box spot and there's a key in it but I just don't know what the needs or how im going to get her filled with lp or even know if those lines are good. Any insight so I can restore this beauty is appreciated
 

Attachments

  • 20261101_095120.jpg
    20261101_095120.jpg
    2.2 MB · Views: 0
First: fluids. Drain and refill the cooling system. Find the crankcase coolant drain likely near or at the temp sensor. Call any LP provider around and they will show up with a truck and fill your tank. The trans is probably ok for now, but new oil and filter. It has an oil bath air filter, u dump out the old oil in the bowl, clean the bowl ajd refill to proper depth on bowl. Check for pos or neg ground and get a good starting batt. Be careful and KNOW first if pos or neg ground. Connect the batt, open the LP valve at the pressure tank, put in N, push the clutch and give it a try.
 
Albers… You don’t mention how mechanically inclined you are…. If you have worked on similar era (‘60’s) cars and trucks, you can likely figure this out. But if iPads and ip addresses are your thing, I think you need to find some local help. Mistakes can be very costly.
 
Albers… You don’t mention how mechanically inclined you are…. If you have worked on similar era (‘60’s) cars and trucks, you can likely figure this out. But if iPads and ip addresses are your thing, I think you need to find some local help. Mistakes can be very costly.
I'm somewhere in the middle! Most equipment i worked on in the navy out-aged me by at least 30 years but this tractor is a little out of my scope. Had a local mechanic come by this morning and he told me to just throw some propane in it and a battery and see what she does. So I'll be changing the plugs and wires as soon as I get paid to get closer to that goal!
 

Attachments

  • 20261104_093808.jpg
    20261104_093808.jpg
    1.9 MB · Views: 0
Nice find. Ive been around MM all my life but none of them were LP. So I can't help much on that portion.
 
I'm somewhere in the middle! Most equipment i worked on in the navy out-aged me by at least 30 years but this tractor is a little out of my scope. Had a local mechanic come by this morning and he told me to just throw some propane in it and a battery and see what she does. So I'll be changing the plugs and wires as soon as I get paid to get closer to that goal!
I agree with docmirror,, change fluids first. There will be some condensation moisture in the crankcase, plus used oil can become acidic when mixed with water.
That's what's called an ASME LP tank, which does not require an inspection like USDOT cylinders. I agree, call an LP supplier and ask if they can come refill the tank.
 
LP: if you have a trailer and plan on keeping/using this tractor, go to Farm & Fleet or a comparable store and purchase the fittings and hose to go from a 20# tank to the 3/8"flare fitting on the tractor. That way you can hook the tank to the tractor and drive it for a half a day. don't turn the tank upside down unless you're going o work it HARD, as in field work, then the tank won't last very long anyway. I use a 10' hose and hang the tank on the back of the seat on the tractor. Where are you located? may be someone in your area that has first hand knowledge
 
Don’t know what you gave for it and I’m not asking but it looks like you got a good starting point for a nice tractor. Tires look good from the picture, set of banana weights on the nose and the tin work looks like pretty good. Good luck with it and keep us posted please
 
Well, guys was able to get the hood off and Take a look through. She needs new spark plugs and wires for sure. Pretty much new wires All around. Had a mechanic come out and check the engine He said it looks great. Just get me a battery and put some propane in it. And we'll be able to try and turn her over. Due to me being in New Mexico where there's not a lot of history of LP tractors, it's extremely difficult to find anybody that'd be willing to come fill it mich less knows anything about lp tractors. But after reading some forums, if I get the right fittings, I might just do it with a small 20 gallon grill tank. My father in law works for airbase so he suggested i use the warm water trick to check if there's any propane liquid left in there. I also bought some manuals! Once those get here next paycheck goes to wires and plugs
 

Attachments

  • 20261105_081010.jpg
    20261105_081010.jpg
    774.9 KB · Views: 0
  • 20261104_093808.jpg
    20261104_093808.jpg
    1.9 MB · Views: 0
  • Screenshot_20261106_112136_eBay.jpg
    Screenshot_20261106_112136_eBay.jpg
    364.1 KB · Views: 0
Every LP truck will have a bucket of adapters for weird applications. They may not want to come just for 10-12 gal fill. Finding the fittings to fill off a bbq tank might be a bigger challenge. You can send a pic of the fill port and let them find the one they need.

I have a cabin in Timberon near Cloudcroft and our lp truck has all the adapters onboard. If you are doing the ign wires might as well do the points and condenser. Find the oval plate on the side of the dist. Use that dist model to get the right set. Or a whole kit with cap and rotor too. Check for spark from the coil output with no plugs in before wiring it all up. Have you moved the engine around at all yet?
 
Every LP truck will have a bucket of adapters for weird applications. They may not want to come just for 10-12 gal fill. Finding the fittings to fill off a bbq tank might be a bigger challenge. You can send a pic of the fill port and let them find the one they need.

I have a cabin in Timberon near Cloudcroft and our lp truck has all the adapters onboard. If you are doing the ign wires might as well do the points and condenser. Find the oval plate on the side of the dist. Use that dist model to get the right set. Check for spark from the coil output with no plugs in before wiring it all up. Have you moved the engine around at all yet?
Yes! The engine does move but I havent been cranking it a ton with a wrench just since I haven't done much to it. I've called just about every propane place near edgewood to see if they can and the rejection is more confusion and "I'll call the manager" than anything. I'll definitely look into the coil output to check.
 
I agree with Doc on the ignition kit but be fore warned again there’s a lot of defective parts out there that will make you scratch your head. Been trying to get a 47 U to run well enough to sell and put a new rotor and cap just cause they were on the shelf and the old ones didn’t look so good. No fire 🤨Put the old rotor back in and it started on the first crank. Also heard it said if you buy a condenser, buy three so maybe you’ll get a good one
 
Do you have a large propane tank at your house for home heating? If so you can set it up to fill the tractor tank off of it.

If you don’t have a big tank, I’d probably look into getting a forklift tank or 2. You can carry them into town to get filled and either modify your tractor plumbing to run directly off the forklift tank or transfer the propane from the forklift tank to the tractor tank.
 
Be cautious on points and timing. Known to preignite and break starter cone. Have seen many Prestolite's welded up.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top