Case VAI loses power when it warms up

Betta7776

New User
Location
Wisconsin
I have a 1942 Case VAI that has me scratching my head. I was running into an issue a few weeks ago where once the tractor got warm it would lose cylinders and eventually wouldnt run at all. I tested the coil on it and found the coil to be bad (main coil was shot), bought a replacement on ebay (same era), tested the new coil (resistance values are much better) and installed it. The tractor starts fine, idles alright but seems extremely low on power. I cant even pull my brush hog up a hill when the tractors warm, it just seems to lose a few cylinders and bogs down whenever I try to push it, especially when warm.

I also took the time to replace the carb with another less rusty loaner with fully replaced guts. I have no idea how to tune the carb so think that might be the issue but would love other ideas, as well as someone who can walk me through how to tune the carb correctly, it only has a main jet adjuster and an idle adjustment, annoyingly the carb has to be removed to get to the idle adjust screw. I replaced the sediment bowl and all fuel lines so fuel is definitely getting to the carb. I do notice if I have the fuel on and the tractor isn't running it dumps fuel out of the air inlet, so I know somethings not right there. Definitely in need of assistance.

Please let me know if any other information is needed and what I should do for next steps!
1793643771377.png
 
I have a 1942 Case VAI that has me scratching my head. I was running into an issue a few weeks ago where once the tractor got warm it would lose cylinders and eventually wouldnt run at all. I tested the coil on it and found the coil to be bad (main coil was shot), bought a replacement on ebay (same era), tested the new coil (resistance values are much better) and installed it. The tractor starts fine, idles alright but seems extremely low on power. I cant even pull my brush hog up a hill when the tractors warm, it just seems to lose a few cylinders and bogs down whenever I try to push it, especially when warm.

I also took the time to replace the carb with another less rusty loaner with fully replaced guts. I have no idea how to tune the carb so think that might be the issue but would love other ideas, as well as someone who can walk me through how to tune the carb correctly, it only has a main jet adjuster and an idle adjustment, annoyingly the carb has to be removed to get to the idle adjust screw. I replaced the sediment bowl and all fuel lines so fuel is definitely getting to the carb. I do notice if I have the fuel on and the tractor isn't running it dumps fuel out of the air inlet, so I know somethings not right there. Definitely in need of assistance.

Please let me know if any other information is needed and what I should do for next steps!View attachment 168680
Loss of power when warmed up could be the need the adjust valves or the fact it is low on compression
 
Upvote 0
Loss of power when warmed up could be the need the adjust valves or the fact it is low on compression
Would that sound like cylinders dropping out completely? It goes from a smooth idle/acceleration to extremely rough which is why I thought it was missing cylinders
 
Upvote 0
Fuel out of the air inlet means the needle valve isn't closing due to improper installation, a bad needle/seat, hole in the float, misadjusted float, binding float etc. Losing power when warm could be a number of things. First that comes to mind is a bad coil or condenser. You replaced the coil with a used one from what I understood. Hard to say if it is good or not. Condensers today are hit or miss. Might get a good one, might not.
 
Upvote 0
Would that sound like cylinders dropping out completely? It goes from a smooth idle/acceleration to extremely rough which is why I thought it was missing cylinders
Yes if the valves are out of adjustment the cylinders can/will stop running on the cylinders out of adjustment and run on 2 or 3 cylinders instead of all 4
 
Upvote 0
Replace your condenser
Should I be looking for a numbers matching part? Are condensers generic? Is it worth just biting the bullet and switching to something like https://www.yesterdaystractors.com/...ersion-Kit-6-Volt-Positive-Ground_1545P6.html, or even using this as an excuse to upgrade to 12v? Im trying to stay cheap for now but if this is the right option im certainly open to it just to avoid more headaches.

Certainly new to a lot of aspects of restoration on these older tractors. Im confident in my abilities to change parts, but not confident in my abilities to find the right replacements.
 
Upvote 0
Valves could be the issue, but are not common on those. Ossues with running when warm is usually electrical, check the coil when its acting up, could also be the condenser, spark plugs or plug wires. Case tractors do not like champion plugs, so if thats what's in there is would start with new plugs of a different brand.
 
Upvote 0
When it's running poorly, take a spark plug wire off, put a screw driver into the wire end and hold it near the block to check for color and intensity of spark. Sounds like a weak coil or condenser with too rich of fuel mixture.
Your leaking needle valve, if constant, needs adjustment. If now and then, the best remedy is to put a 1/8" ball valve at the carburetor for a shut off. When all sealed up properly, and the needle valve leaks, the air intake can fill with gas as you know. When you go to start the engine a glug of gas will get sucked in and go directly to the cylinders. Tractor won't start and the gas goes down to the oil.
 

Attachments

  • Screenshot_20261011_220547_Gallery.jpg
    Screenshot_20261011_220547_Gallery.jpg
    178.3 KB · Views: 0
Upvote 0
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top