Troubleshooting Hydraulics on 300U

I have a 300U that we've owned for a while, but the steering has always been a bear, especially with the loader on it. My project for this winter is to pull the hydraulic reservoir cover and rebuild the valves, clean the pickup, etc, but I could use a little help getting my head around the hydraulics, which are pretty new to me.

This tractor has factory power steering, which doesn't seem to work, as well as a fast hitch on one valve and a pair of quick connects on the other.

From what I've been reading here, the most likely cause for the power steering not working is the valve in the safety regulator being clogged, which I'll fix, but I don't fully understand what causes a deadhead condition or if the plumbing on my tractor is done up right. Would love some advise on what looks good here and what doesn't (under all the grease and mud).

Front valve, going to the disconnects:
PXL_20261107_221944275.jpgPXL_20261107_221952014.jpg

Back valve, going to the fast hitch, and regulator:
PXL_20261107_222107911.jpgPXL_20261107_221814267.jpg

Fast hitch hookups and quick couplers:
PXL_20261107_221851145.jpgPXL_20261107_222001563.jpg
 

Attachments

  • PXL_20261107_221916585.jpg
    PXL_20261107_221916585.jpg
    2.1 MB · Views: 0
In your second pic. The inner block with the 4 bolts is the unloading valve and regulator. The dead head or high pressure is caused by the orfice with screen being plugged. When removing the 4 bolts there is a strong spring so be careful removing. Using a screw driver remove the orfice and screen, probably plugged right up with debris. Remove the unloading valve piston and renew the oring. Get the OEM oring and not a will fit. The screw below the piston does not have to be removed as it takes a special tool but make sure the ball has spring pressure against it . Remove regulator valve that the heavy spring is against and clean complete valve throughly. Will also need new gasket for the cover and make sure oil passage in cover is open and clean. The unloading piston can be installed in a vice and compress the pin to open the bypass hole in the piston, to clean . Hope this all makes sense.
 
The Double acting Single acting Control on the front valve is not aligned with the Cheap tin riveted on position stop. It is too far CCW. there seems to be a bent rod holding a lever forward that (and the turned control) can cause dead heading. good luck with it. there are 10s of posts on 300 and 350U power steering Many by Me Jim
 
In your second pic. The inner block with the 4 bolts is the unloading valve and regulator. The dead head or high pressure is caused by the orfice with screen being plugged. When removing the 4 bolts there is a strong spring so be careful removing. Using a screw driver remove the orfice and screen, probably plugged right up with debris. Remove the unloading valve piston and renew the oring. Get the OEM oring and not a will fit. The screw below the piston does not have to be removed as it takes a special tool but make sure the ball has spring pressure against it . Remove regulator valve that the heavy spring is against and clean complete valve throughly. Will also need new gasket for the cover and make sure oil passage in cover is open and clean. The unloading piston can be installed in a vice and compress the pin to open the bypass hole in the piston, to clean . Hope this all makes sense.
Thank you, this is a great breakdown of how to clean out the regulator. I had been looking at the parts diagram, but I was having a hard time visualizing how the whole thing came part.
This doesn't actually sound so bad now!
 
The Double acting Single acting Control on the front valve is not aligned with the Cheap tin riveted on position stop. It is too far CCW. there seems to be a bent rod holding a lever forward that (and the turned control) can cause dead heading. good luck with it. there are 10s of posts on 300 and 350U power steering Many by Me Jim
Are the flats of the control supposed to be parallel to the tin stop? If that's the case, the rear control is probably too far CCW too then, right?
I'm not surprised that homemade lever isn't at the right angle either. It's a steel corner bracket bolted onto the corner of the reservoir then that bolt looped through it to act as a "stop". I'll see about straightening that too.
I've read most of your posts and appreciate all of the info you have shared over the years. It has been really helpful into leading up to making this post. It's actually partly what made me decide to tackle this in the first place.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top