3000 HYD O-RING DILEMMA

Is there a certain kit of O-rings that you can buy that would contain most of the O-rings needed to finish replacing everything needed for my top lid cover. I have an assortment of nitrile O-rings SAE. Some of them are so close I can't tell the difference but is there something I should look for or do they need to be perfectly fitted and not just close. When I started this project I bought a top lid cover gasket with O-rings to go along with replacement. A helper (meaning well), replaced some while I was working on something else and got them mixed up and I don't know where I'm at now LOL any advice.
 
They sell the full top cover kit here, with all of the o-rings, seals and gaskets for the top cover, but at the moment I am getting a "403 Forbidden" when I click on the "Buy tractor parts here" button at the top right of ever page on this we site.
 
They sell the full top cover kit here, with all of the o-rings, seals and gaskets for the top cover, but at the moment I am getting a "403 Forbidden" when I click on the "Buy tractor parts here" button at the top right of ever page on this we site.
Thanks, I'll check it out!
 
Every o-ring will for to spec except the unloader, the unloader is a -114. It will fit the valve nice, once installed in the bore it should float easily. The unloader compensates for differential pressures on either side it floats in the bore and should not have to be coached to mover. That's why you cannot use standard O-ring fit specs on unloader applications the engineer specked it different for this application.

If in doubt on the other O-rings look up the specs and measure it out. I have posted the positions of the O-rings and the dash size they are lost in space when the forum switched over to its new state. You may find the dash size on CNH web site. My standard off the shelf O-ring kits do not include one are 2 of the O-rings needed I would have to look at them they are a -215 are -217 my guess.
 
Thank you very much for all your help. The things I'm learning are just amazing! The difference between a Duro 70 and 90 are one thing. I've read so much on that, I'm still not sure which ones have to have the 90s and so I guess I'll just have to buy all my 90's, not sure. The bad part is, that I've replaced orings on almost everything In lid cover area before I began to wonder about the Duro #'s. I made sure they were all Nitrile but not Duro specific.
Now I wonder if I need to check on unloader valve oring!
 
Every o-ring will for to spec except the unloader, the unloader is a -114. It will fit the valve nice, once installed in the bore it should float easily. The unloader compensates for differential pressures on either side it floats in the bore and should not have to be coached to mover. That's why you cannot use standard O-ring fit specs on unloader applications the engineer specked it different for this application.

If in doubt on the other O-rings look up the specs and measure it out. I have posted the positions of the O-rings and the dash size they are lost in space when the forum switched over to its new state. You may find the dash size on CNH web site. My standard off the shelf O-ring kits do not include one are 2 of the O-rings needed I would have to look at them they are a -215 are -217 my guess.
When ever I try to use my generic oring kits, the cover will always ooze and leak. And in a few places there are "flat cut" orings. So you can expect to do it twice. First time with generics, and the second time with New Holland rings. Its a crap shoot.
 
Thank you very much for all your help. The things I'm learning are just amazing! The difference between a Duro 70 and 90 are one thing. I've read so much on that, I'm still not sure which ones have to have the 90s and so I guess I'll just have to buy all my 90's, not sure. The bad part is, that I've replaced orings on almost everything In lid cover area before I began to wonder about the Duro #'s. I made sure they were all Nitrile but not Duro specific.
Now I wonder if I need to check on unloader valve oring!
Have you looked at the online parts diagram(s)? They have the specs for the various O-rings as well as part numbers and price if you want OEM.

 
When ever I try to use my generic oring kits, the cover will always ooze and leak. And in a few places there are "flat cut" orings. So you can expect to do it twice. First time with generics, and the second time with New Holland rings. Its a crap shoot.
Like anything else its up to the installer to confirm fit and quality. CNH O-rings are made in China everything these days are a crap shoot : (
 
Have you looked at the online parts diagram(s)? They have the specs for the various O-rings as well as part numbers and price if you want OEM.

Yes I've looked at the online parts diagrams that's all been very helpful. I don't know where I'd be without you guys cuz you have given me so many different things to look at and basically I'm overhauling everything if it needs it or not. The O-rings thing is really kind of hard to to follow but I'm catching on!
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top