2950 fuel injector issue.

Our 2950 diesel tractor has been sitting for at least 15 years due to a never fixed hydraulic issue. Anyway, we decided to have a look at it to get it back in working order.
Started with an oil change, new filter, new inner and outer airfilter, drained the old fuel, new fuel filter.
It was tough to get her going, but it started eventually. Ran like crap, really loud knock, couldn't quite figure out where it came from, also white exhaust smoke.
Started with Testing each injector by cracking the individual pressure fuel lines, 5 of the six responded immediately when the fuel supply was cracked open, one injector did not respond when the fuel supply was cracked, but the white smoke disappeared and the knock sounded less?
So we replaced the 'faulty' injector, which was a son of a gun to get out. Started it up with the new injector, the knock is barely noticeable or maybe I just hear it in my imagination, but we still have the white smoke, which stops when we crack the fuel supply to the new injector.
Why would that be? Where do we go from here?
Thinking of opening up the valve cover next to see if anything looks odd, just don't want to start tearing things apart if there are other things we could look at prior?
Help please.
 
I suggest to check compression on cylinder emitting white smoke. I also recommend checking engine valve rocker arm clearances. Did you put any fuel conditioner &/or oil in fuel tank?
No we didn't put any fuel conditioner in the tank. I think we have some fuel stabilizer kicking around, maybe I'll add some of that to the fuel today.
Curious as to what we will find under that Valve cover............... I still hope it's a simple fix.
 
If tractor was under my supervision I'd be very concerned what problem caused tractor to be put out of use 15 yrs ago.
That will be the next project once the engine runs again. From what I remember the hydraulic system completely failed. The main hydraulic pump was replaced but that wasn't the problem. I really don't recall what was all tested back then, only that the engine started acting up on top of the hunt for the hydraulic problem. At the time this was our chore tractor and cows want to get fed......... no time to play around with engine and hydraulics. The tractor was replaced so the chores could get done and here we are, life slowed down, kids moved out, let's tackle a project....... know what I mean?
 
I've read over my many years associated with repairing tractors of many hyd pumps being replaced prior to good hyd diagnostic procedures being performed only to determine that the replaced pump wasn't the hyd problem & was in fact a good pump. I highly recommend when hyd diagnostic procedures are initiated to change hyd filter. Also check/clean hyd oil suction screen.
 

Attachments

  • Screenshot 2021-04-25 090746.png
    Screenshot 2021-04-25 090746.png
    139 KB · Views: 0
I've read over my many years associated with repairing tractors of many hyd pumps being replaced prior to good hyd diagnostic procedures being performed only to determine that the replaced pump wasn't the hyd problem & was in fact a good pump. I highly recommend when hyd diagnostic procedures are initiated to change hyd filter. Also check/clean hyd oil suction screen.
Oh absolutely!! Back then we didn't know quite as much as we do today, not saying we know too much today either. Hahaha. Just trying to say we learned our lessons with throwing parts at problems and yes, that main hydraulic pump was one of the lessons learned and money thrown out the window.
Didn't get around to do a compression test or take off the valve cover today. Temperatures are dropping and we worked on moving the tractor into the shop now, Canadian winter is going to be knocking on our doors this coming week.
 
If it's been sitting for 15 years you should clean out the complete fuel system. Start with the tank, dump the old fuel, clean the tank, blow out the lines, replace the filters, rebuild/clean the injection pump and maybe just replace or rebuild all the injectors. Any diesel fuel that old is like a sticky, old, smelly mess which won't even burn. How about the tractor? Sitting outside or shedded? Moisture in cylinders? Better check all that and run it before you consider the hydraulic problem and create further damage.
 
Our 2950 diesel tractor has been sitting for at least 15 years due to a never fixed hydraulic issue. Anyway, we decided to have a look at it to get it back in working order.
Started with an oil change, new filter, new inner and outer airfilter, drained the old fuel, new fuel filter.
It was tough to get her going, but it started eventually. Ran like crap, really loud knock, couldn't quite figure out where it came from, also white exhaust smoke.
Started with Testing each injector by cracking the individual pressure fuel lines, 5 of the six responded immediately when the fuel supply was cracked open, one injector did not respond when the fuel supply was cracked, but the white smoke disappeared and the knock sounded less?
So we replaced the 'faulty' injector, which was a son of a gun to get out. Started it up with the new injector, the knock is barely noticeable or maybe I just hear it in my imagination, but we still have the white smoke, which stops when we crack the fuel supply to the new injector.
Why would that be? Where do we go from here?
Thinking of opening up the valve cover next to see if anything looks odd, just don't want to start tearing things apart if there are other things we could look at prior?
Help please.
After sitting 15 years could some piston rings be stuck?
 
If it's been sitting for 15 years you should clean out the complete fuel system. Start with the tank, dump the old fuel, clean the tank, blow out the lines, replace the filters, rebuild/clean the injection pump and maybe just replace or rebuild all the injectors. Any diesel fuel that old is like a sticky, old, smelly mess which won't even burn. How about the tractor? Sitting outside or shedded? Moisture in cylinders? Better check all that and run it before you consider the hydraulic problem and create further damage.
Yes, we've drained the tank completely, new lifter pump, new fuel filter. We are planning on replacing all injectors, but for now we just replaced the faulty one.
Not going to touch the hydraulic problem until the tractor runs good.
 
Had the chance to work a bit more on the tractor. Couldn't do a compression test because our test kit must have grown feet and wandered off somewhere.
Took the exhaust manifold off to make access to the valve cover and injectors a bit easier. Bolts holding down the manifold were nice and dry for the first 3 cylinder exits, the bolts for the 4th one were wet pretty much the hole length and the bolts for the 5th and 6th cylinder ports were partially wet. Of course all the ports had quite some carbon build up once the exhaust manifold was off. Port 4 had moist carbon build up.

After that I removed the valve cover, the gasket was intact and in good shape, so no leaks there. But it had quite a bit of sludge accumulation under that cover.
We turned it over and everything seems to rock/move, guess that's not going to tell me much.
Would have liked to do a compression test, but that will have to wait until I can get my hands on a new test kit.

Question though: How could the bolts which hold the manifold on to the engine block have moisture on them? Is that just coincidence and the moisture can only come from the exterior? Or is there another scenario where the moisture could have come from? Broken seal between the head and the exhaust manifold? Didn't have any visible leaks though on the engine block.
 
We turned it over and everything seems to rock/move, guess that's not going to tell me much.
Secondly and just as important is checking for valve lash on the problem cylinder. Turning the engine so one valve is completely open and checking the opposite valve of that cylinder is an easy way to check. With the valve cover off it would be foolish not to adjust the valves anyway and it should be done before a compression test, maybe even before and after wouldn’t be a bad idea.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top