(800) 853-2651
SHOP NOW

Search results

  1. L

    MF's compatability

    I have a MF-135 with a good transmission and rear end and a MF-50 with a good continental engine. Will they bolt up and work together?
  2. L

    MF's

    Does the transmission of a MF-135 bolt up to a MF-50?
  3. L

    MF 135 Throttle linkage

    There are two rods that make the linkage. One goes from the throttle to the carb/gov lever and a shorter one back to the carb. Which rod goes to which hole? There are two holes in the lever, one at the top or end of the lever and one close to the shaft from out of the timing cover.
  4. L

    MF 135 Lift cover and draft control

    Since I do not see any plowing in the future for this tractor is there any way to inactivate the draft control while keeping the position control working?
  5. L

    Thanks to Masseynut and DavidP

    I did indeed have to turn my flywheel down to 44.5 and the fingers came right up to the gauge. I wanted to be sure you guys saw my thanks. I would have had a very hard time without your help.
  6. L

    MF135 clutch release fingers won't adjust close to gauge

    I have a MF135 split and have replaced the dual clutch discs. I bought the tractor and do not know it's history other than the maintenance was not performed by a MF mechanic, a lot of telltale signs throughout the tractor. I made the finger height adjustment gauge with a 1" recess as shown in...
  7. L

    MF135 clutch springs

    I bought a 135 and it is a mess. Somebody has tried to work on it and didn't know what they were into. Anyhow the clutch was extremely stiff so I split the tractor and found the dual clutch has three sets of three different colored springs in it and they are different strengths. I cannot seem...
  8. L

    Fuel linkage

    does anybody know where I might find a lever assembly for a MF 135 Perkins gas AG3-152. It comes through the dash panel and fits to a brackett below. Dealer wants $360. dollars for a replacement. That just seems highly unreasonable.
  9. L

    Voltage regulator

    Anybody know where I can get one of the aftermarket external regulator to mounts on the 12v Delco-Remy altenator on my MF50?
  10. L

    MF values

    I'm looking to trade my MF-50 for a MF 230 both tractors are in good condition except my 50 has a slight roar from a bearing in the transmission. The dealer wants to trade before I split and replace the bearing. My tractor has good wheels, tires, paint, hydraulics, power, and never gives me a...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top