(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. C

    Re:

    My G used to be my spraying tractor,and several years ago as I was using it to spray,the intake rockers started squeaking.I decided to drill small holes above the intake rockers[do not remember the bit sizes]and it solved the squeak.I never have seen a negative result from doing that.I only...
  2. C

    JD 510B TLB

    We have a customers John Deere 510B TLB that came into our shop with a slipping direction reverser.I put gauges on the pressure port[line pressure]lube port,and forward clutch pressure port.The line pressure was low at 145,which I shimmed to 165.In neutral the lube pressure is 10psi.When I shift...
  3. C

    Re: MM HF combine

    I bought an 88 harvester about 4 years ago and when I get a chance I enjoy running beans through it,pulling it with a Farmall 400D.It was in running condition when I got it.I am hoping to run about 6 acres through it next week.
  4. C

    8670

    I have a friend who brought me an 8670 to try to solve a transmission problem.Starting in 1st upshifting is fine until the 9th-10th shift,at which time it will stall the engine,unless it is clutched,at which time it will go up to 16th OK.Then downshifting it almost stalls with the 8th-7th...
  5. C

    Value of restored 1922 Fordson

    Three years ago we restored a 1922 Fordson for a family,and one of the members wants to buy out the others'share. The extent of the restoration incuded rebushing and new bearings in the front axle,a valve job with 4 valves and 2 guides.We replaced the manifold assembly with new,and most of the...
  6. C

    White 6175

    We had a customer bring in a White 6175 that is transferring hydraulic oil into the transmission at 1-2 quarts per hour.The service manual does not show where the transfer could be taking place,and I was wondering if anyone here knows where to start looking.Thank you for your help.
  7. C

    White 6175

    We had a customer bring a 6175 in that is getting hydraulic oil into the transmission.I can not find anyplace in the service manual that helps me find where the exchange could be taking place. Does anyone here know where to look? It is taking oil out of the hydraulic reservoir and putting it in...
  8. C

    3020 balancer

    Does anyone know how much bearing clearance the 3020 balancer bearings are to have before they need to be replaced? I had a customer bring one in to the shop today to be checked.It has .007-.008,which seems a bit high,but all the service manual says is to rebuild it when it has too much wear.
  9. C

    Hard starting 466

    About 30 years ago I installed an RG6466A Deere engine in an IHC TD20C dozer for a customer to replace a tired, and very expensive to rebuild ,DVT573.He was very happy with the repower until 2 years ago when it would no longer start at 10degrees F without aid.It now needs to be 40 to start with...
  10. C

    Combining soybeans with my 400D and MM HF combine

    Tuesday evening and Wednesday I was able to take enough time off work to combine about two acres of soybeans with my 400D and my Minniapolis Moline HF combine.It was a lot of fun,but not something I would like to make a living at, as farmers would have 50-60 years ago.
  11. C

    MM HF combine

    I just bought a Minniapolis Moline model HF combine serial 39403297.Does anyone know the vintage of this machine?
  12. C

    400diesel

    I got to enjoy 4.5 hours plowing with my 400 diesel yesterday and today.I like the sound of that engine, and the way it pulls the fast hitch 3-16.
  13. C

    Got to spend a day spraying with my 400D

    I finally got to spend a day spraying 140 acres of corn with my 400D.This was a job my '47 JD GW has done since 1987.I have kept a record of the fuel burn on my GW, and with the lite job of spraying,it's fuel burn was 2.0 gallons per hour.The 400 burned 1.375 per hour.The wide front on the GW...
  14. C

    Got to plow

    I finally got to use the 400D I bought in Nov of 2010.I recently bought a fast hitch 3-16 and got a chance to use it for about an hour, till I got rained out.I had to do radiator recoring, water pump rebuilding, pedistal etc etc, which is the reason for the delay in use.I really enjoyed getting...
  15. C

    block water headers

    After playing with my JD G and GP for 24 years,I bought a 400d and found the cooling system very dirty.I removed the rear water header which has part of the header rusted away.I went to my local salvage yard and found thin steel and 1/4 inch steel plates.which should I use and why do they direct...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top