(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. C

    Replacing Starter Switch

    I've got to replace the starter switch on my Ford 641 with 4 speed transmission. Removing the shifter plate from the transmission looks pretty straight forward, but was wanting to know if there are any gotchas in there that I should be aware of. Does the cover just lift straight off or are...
  2. C

    Fuel Line Routing

    I have a question pertaining to the fuel line on a Ford 641 tractor. First, how was the fuel line originally routed from the fuel cut off valve to the carb? Does it run down "behind" the intake/exhaust pipes? That's the way mine is routed with a combination steel and rubber gas line. I'm...
  3. C

    Carb Pouring Gas

    Folks I'll tell you right up front that I have posted this same question on another forum, so I apologize in advance for the redundancy, but I need more help. As the subject says, the Marvel Schebler TSX 765 carb on my tractor is pouring gas out of the air intake. I have taken it apart and...
  4. C

    Hydraulic Control Valve

    I'm posting this question for my brother. He has a '53 Jubilee/NAA that has a problem with the hydraulic lift. It was leaking down real fast and eventually got to where it wouldn't lift at all. It was also hiccupping real bad when it did get the load up. He took it to a shop for repairs and...
  5. C

    Generator Warning Light

    I've got a generator warning light on my 601. Now that I have converted over to 12 volts, I was wondering if I could some how use the warning light in conjunction with the new alternator and, if so, how would you wire it? I could just use a amp meter in lieu of the gas gauge, but would like to...
  6. C

    Front Wheel Alignment

    I've noticed that the wheels on my '61 641 are not aligned correctly. When I move one wheel to where it is setting straight ahead, the other is pointing to the outside quite a bit. Do I correct this back at the steering box or the tie rods? It looks to be too much for the tie rods, but not...
  7. C

    Pitman Arm Seals

    I've got a pretty good leak coming from the seals behind the pitman arm. Can those be replaced from the outside, or do I have to remove the steering box to replace them? Thanks
  8. C

    Lift Problem

    I recently picked up a Ford 641. The tractor had been sitting outside in the weather for well over a year. I've been working to get everything cleaned up and working, but I am having trouble with the touch control lever on the lift. When I first got the tractor home, the touch control lever...
  9. C

    finish mower

    Do you folks think that a ford 641 could handle a 6 ft. finish mower? Everybody around here says to stick with a 5 ft. mower. I've got an area of grass that's too small for a rotary mower, but too much for my riding mower. I thought I might pick up this 6 ft. finish mower to do it all? What...
  10. C

    Need help, Wiring Quagmire

    I recently rescued a Ford 641 from the clutches of a giant oak tree on a fellows farm. He said it had been setting there for about 1 1/2 years. To make a long story short, we drained the tank, put in fresh gas and a good battery and it cranked right up after about 5 spins. Here is my current...
  11. C

    Ford 600 fenders

    Can someone please tell me if the Ford 600 Fenders are the same as the NAA with the raised Ford script? If not, can you tell me how they differ, or better yet, post a photo of them. Thanks for your help.
  12. C

    Valve Job Cost

    Looking at buying a 641 that has an unbelievably straight body, new tires, excellent hydraulics. The problem is it smokes. The owner stated that according to his compression check, the rings were ok, but the tractor needed a valve job.. The price is right even with the smoking, but I was just...
  13. C

    Which 12 volt battery for Jubilee

    I've searched for this, but couldn't find anything. Can someone tell me which 12 battery will fit in the battery tray of the Ford Jubilee? Thanks
  14. C

    Tractor is cranking without the switch on

    My Jubilee was converted to 12V by its previous owner. I haven't been able to use the starter button and I thought it might be the solenoid as it was some aftermarket 4 post design. I put on a new solenoid and when I went to put on the ground cable, the tractor started cranking on its own. I...
  15. C

    Waxy looking gunk in fuel tank

    My Ford 4000 started shutting down on me the other day after running for about 10 minutes. I'd let it sit and it would start back up and run for about 10 minutes. It would repeat this all day. Plenty of diesel fuel in it, but when I checked the level, there was a bunch of waxy looking gunk in...
  16. C

    First paint job, few questions

    Going to be trying my hand at painting my Jubilee soon, but I don't have a spray gun yet and not sure if I have enough air to do it with. I've only got a 3 hp compressor with a 30 gal tank, but it does a pretty good job of keeping up with some of my air tools. I was wondering if some of you guys...
  17. C

    8N/NAA Paint, the same???

    Is the paint for the NAA the same as the 8N, or are they different shades?
  18. C

    Transmission Fluid Levels

    Where do you check the oil levels in the transmission/lift/differential on a 1974 Ford 4000? I can't seem to find a dipstick or any way of checking the fluid levels. Thanks
  19. C

    Ford 3000 What to look for

    Hey folks. I'm going to be looking at a Ford 3000 tractor tomorrow and was wondering if some of you folks might be able to give me some pointers or things I should be checking out. I'm stepping up from a Ford Jubilee to this diesel and just am not familiar enough with them to know what to look...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top