(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. W

    1950 8n pto leaking

    Good evening. I recently pulled the pto shaft and replaced 703 9N703, D9NN703BB Oil Seal (power take off) 715 9N715BC Bearing Assy. (PTO shifter and shaft) 735 9N735B Sleeve (power take-off) 754 9N754 Snap Ring (power take-off shaft bearing) 4129 9N4129, C5NN747 Gasket (power...
  2. W

    1950 8N hydraulic lift control lever will not move

    the lever will not move. I removed the top with the linkage and I cannot find why it doesn't move. any ideas?
  3. W

    1950 8N, hydraulic lift lever

    the hydraulic lift lever became hard to lift about a month ago. now the lever will not move over 1" and when it does move the draft control valve moves a little. I changed the lube, inspected the pump. the pump does lift when manually moving the internal rod. any ideas. I was wondering...
  4. W

    fuel flow issues

    I have a side mount dist 1950 8N. due to the gas tank rusting up I replaced the fuel tank, fuel line, fuel bowl, and the carb. I realize not all of this was necessary but I did it. I still do not have good fuel flow from the tank. I have replaced the fuel bowl twice. to test it I took the...
  5. W

    50 8N question

    what symptoms are experienced from distributor weights not working? I am working on a problem and think I have it narrowed to that.
  6. W

    starter question

    my starter seems to drag and makes a lot of noise. does this look correct? and as soon as I remember how to insert the picture it will help [/img]
  7. W

    distributor weights

    I replaced the distributor bushing on my side mount dist. last night. when I looked at the weights the pins on the bottom have a groove in them where they slid in the slots. obviously the best move is to replace, however can one weld the grooves up and the hone them to size? Inquiring minds...
  8. W

    Always Amazed

    I have been trolling this forum for about two years. I am constantly amazed at the wealth of information you folks share. Thanks for all of you N series Masters for sharing your knowledge.
  9. W

    another flywheel question ref timing marks

    I have a late 1950 8n and the only marks I find on my timing wheel is a diagonal line with a round mark in the middle. Is this correct?
  10. W

    Maybe off topic. any Texas people here?

    I have been lurking around for a while. And I have asked a few questions and been given fantastic advice. the knowledge base here is awesome. I am just wondering how may Texans are on here. I am in the Weatherford Texas area. Thanks
  11. W

    how much fluid in tires

    I realize this is potentially a very subjective question. How much fluid (water/antifreeze for example) should I put in the tires of my 8n? I do just a little plowing and discing mostly mowing. but when I try to plow and disc my rear tires spin. Thanks in advance.
  12. W

    Resistor or no resistor

    Ok, I will preface this with I know you guys have answered this over and over. but I need your assistance. I have a 1950 8n side distributor. 12volt conversion. one wire on alternator. When I got it it didn't have a resistor, Do I need a resistor? Thanks to any of you that will...
  13. W

    8n starter

    my 8n starter was dragging, and then the magic smoke came out. any suggestions.
  14. W

    1950 8N question

    OK, everyone. this is my first post after lingering around for a while. first, I have a 1950 8N, side distributor. question about point gap. I gapped the points at .025 like the manual said. didn't fire. set them at .015 like the old timer at the parts house said it fired. I have been...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top