-
Y
Model B Restoration
I am gearing up to restore my 1948 Model B. Im in need for a parts tractor as my 48 has different rear rims, the hood is beyond repair, the grill is beyond repair, and the sheet metal (tool boxing below the steering column is missing). Im seeing lots of parts tractors that predate mine and are...- Yudt06
- Thread
- Replies: 3
- Forum: Allis-Chalmers
-
Y
Ford NAA Reproduction Carb
I know the original Marvel carb cant be beat but has anyone had any luck with the high end reproduction Carbs? I just ordered one from Steiner because I refuse to buy a cheap reproduction from ebay or Amazon. Its going on an NAA. Anyone have any luck with them please let me know Ryan -
Y
Ford 711 Loader (soundguy)
I have a hydraulic leak from the elbow located at the bottom of the hydraulic cylinder on my Ford 711 Loader. After disassembly it appears there was some type of a rubber O-Ring or Nylon Flat washer that has since worn away hence the leak. For my 711 Guys like Soundguy can anyone guide me to... -
Y
NAA pump relief valve
I recently purchased a new hydraulic pump relief valve for my 54 NAA. This one isn?t the same as the original (ball bearing at the base of the spring). Has anyone replaced this valve with an aftermarket? And has anyone had any issues with it ? Thanks -
Y
54 Ford Headlight Wiring
Getting ready to install new 12v seal beam lights on the tractor. My question is what gage wiring should I use? -
Y
711 Loader Help
So I got my new 711 hooked up to my NAA. Worked well for a week and now it is slow to raise if it even raises at all. I?m running it off of an original selecter valve from ford. My three point works just fine but when I switch over to loader I have the issues. I also noted if the loader is... -
Y
Ford 711 loader
Got the loader all hooked up to the 54 NAA. Much to my surprise the cylinder was solid. Couldn?t tell you the last time it functioned. Now off to sandblasting and powder coating -
Y
711 Loader on a NAA
I?ve posted here several times over the past 4 or 5 years regarding a 711 loader on an NAA. I bought the loader back then and didn?t realize at the time how scarce the brackets and hydraulic valve to run the loader were on my model. Needless to say I?ve acquired the hip bracket for the NAA... -
Y
12v conversion
I just ordered a new 1 wire alternator kit for my naa from Steiner tractor. Just curious if the regulator needs to be replaced as well? Any other upgrades I need to make that I?m not thinking of ? Also any suggestions on which battery to run with it? Thanks -
Y
12v Conversation
Getting ready to convert my 54 NAA for 6v to 12v. I know they sell kits for this project. I know my lights will need to be updated to 12v but what other parts might I need beside the alternator and wiring ? Do I need a new distributor and such? Any input or suggestions on what conversation kit... -
Y
711 Loader
Hey guys (especially Soundguy haha) I have obtained all the proper brackets (esp for the plate that mounts under the steering box) and selec-trol valve to mount my 711 loader on my 54 NAA. Can you guys please post so or send me some photos of the Brackets on the NAA so I can properly... -
Y
Naa Select-Trol Valve
Every now and then I post to see if anyone has a Select-Trol Valve for a 53/54 NAA for sale or have seen any. I have a 711 loader im trying to install with all factory parts. Thanks Ryann -
Y
NAA Diverter Valve
Anyone out there have a Diverter Valve for a 54 Ford NAA for sale ? Thanks -
Y
Ford NAA Paint
Need to paint the fenders on my 54 NAA. What type of paint does everyone suggest. Also, please reccomd a primer Thanks -
Y
NAA Hydraulic Diverter
Anyone out there have a Hydraulic Diverter value for a NAA for sale? Looking to run my Ford 711 loader the original way -
Y
Select-Trol Valve
Any have an extra select-trol diverter valve for a 53/54 ford up for grabs ???? Looking for one to run my 711 loader. -
Y
Wanted! Ford NAA Remote Hydrulic Valve
Does anyone have or know where I can get my hands of a NAA hydraulic remote? Thanks -
Y
NAA one arm loader bracket
This message is a reply to an archived post by soundguy on January 26, 2015 at 11:59:25. The original subject was "Re: NAA one arm loader bracket". Hey soundguy Looks like it's been a while since anyone has been talking about the hip mounting bracket for a NAA. I need to buy or fab one...- Yudt06
- Thread
- Replies: 9
- Forum: Ford 9N, 2N & 8N
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy