(800) 853-2651
SHOP NOW

Search results

  1. B

    how to remove 545 oil pan

    I have the manual and have read it. It says to move the front cross member forward. My 1 1/8 socket is way too loose and the 1 1/16 won't fit. What size are those and how do you get them loose? They are insanely tight and there is no room for wrenches to swing
  2. B

    Ford 545 backhoe, if you know about these

    the front side weights weigh 210 pounds each with no place to hook a hoist onto. How do you remove and replace these? they bolt on but there must be a way to hold them while removing the bolts and then again to replace them. thanks
  3. B

    making a nice ditch

    What kind i of tool or implement do I need to make a nice ditch along my driveway? Its rocky soil and I have a Ford 545 backhoe, a Ford 9N and a Farmall model H Thanks!
  4. B

    tire rating

    Will someone please tell me about the B1 and B4 ratings for tractor tires? Thanks
  5. B

    Fordson super major information

    A friend has asked me to help get this thing running. It has been sitting quite a while. I dont know about diesels and we will get the I&T manual but for now--how can we tell if the injectors are ok and where is the injector pump? We cleaned the fuel tank and lines and replaced two fuel filters...
  6. B

    Fordson Super Major fuel filter

    We are starting to work on a Super Major that has been sitting a long time and the canister for the fuel filter is empty. We got an element for it but it falls deep into the canister. Is there supposed to be a spring or spacer in the canister before the element goes in?
  7. B

    why are 9Ns repainted red?

    I have a 9N and a 2N and both have been painted red twice. Any idea why? Are they trying to fool someone into thinking it is an 8N?
  8. B

    how do you get a new coil to work?

    12V 1941 9N, rebuilt engine, new coil, points, distributor shaft bushings, blah blah. When I got ready to start it, no fire to the plugs and I figured out that the straight contact on the coil was nowhere near the contact on the dist cap so I bent it forward. It started and ran very well for...
  9. B

    grinds, wont go into gear

    I have been working on antique Ford cars and pickups for almost 50 years so I recognize most of the parts on my 9N. I carefully checked all the parts while the tractor was split. The throwout bearing, pressure plate and clutch disc look good. There is no slop in the throwout shaft and I...
  10. B

    When using the NAA 530-B hydraulic Piston

    does the NAA 473-A Back-Up Washer fit into the groove with the o-ring? does it go in the groove on edge and close to the crown of the piston or on the skirt side? Thanks!
  11. B

    ZANE says

    Zane says to use the O-Ring type Piston for the Hydraulic Lift, and external_link says to include the NAA 473-A which is (1939-54 Back-Up Washer Optional for 9N, 2N, 8N When Used With O-Ring NAA533-A and NAA473-A) Exactly where does the 473A go?
  12. B

    good radiator

    I have seen some posts saying the chinese radiators dont fit What are good radiators for a 1941 9n?
  13. B

    Woods RM59

    I am positive that the propeller shaft is too long. It makes a lot of racket when running. Any ideas to adjust it? Are shorter shafts available?
  14. B

    Another 'why wont it start' thread

    Freshly rebuilt engine, 1941 9N, has voltage to the new coil, hot battery, no spark at the plugs. The distributor has new bushings and shaft, new points set at .015 and the condenser tests good. I used the meter to check continuity thru the distributor, no grounds. Its 12V and I am using the...
  15. B

    that PTO bearing

    When I got this 9N, the PTO would not stay engaged and the PTO bearing housing was so wallowed out that I thought the bearing was bad. The new bearing was Made in China. I got the PTO shaft out and looked at the old Made in USA bearing. Its got a little free play but not much more than the...
  16. B

    lazy, worthless, no account

    and too cheap to buy the valve adjusting tools. I bent a piece of wire and used it to set my valves. Its offset to clear when you use the other end.
  17. B

    do you use the 8N spacers on your 9N front axle?

    The FO-4 shows parts 8N3024 and 8N3027 spacers and my 41 9N looks like it sure does need them. Do you put them on your 9N?
  18. B

    whats the deal with my seal?

    All the vendors are selling nca1190A for front wheel grease seals, but as you can see, there is no way these will fit the spindles on my 1941 9N pictures show both seals and the 1190A on my spindle whats the deal? my engine is almost complete
  19. B

    how do you guys fix the wallowed out pivot hole in the axle?

    The holes are stretched out on the front mount and the axle. I know I can build it up with weld but what then? How can I get the holes round again?
  20. B

    What holds the long throttle rod at the rear?

    If this picture works, the tab with two holes was holding the end of the long throttle rod. Looks homemade. What does the factory piece look like? Untitled URL Link
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top