(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. Absent Minded Farmer

    H brake questions....

    How much thread should be exposed on the brake rod? I have two out of three H's that have about 1 1/2" showing. Both of those lock on about the fourth or fifth click of the brake pedal latch. My H that gets used has about two threads showing above the lock nut & is set to two clicks. That had...
  2. D

    Clutch pivot

    The hole where the clutch shaft goes through the bell housing on my 6610 appears to be wallowed out. This causes the clutch to not adjust well. Has anyone else seen this issue, and is there a bushing?
  3. Blackhole49

    Re: Honda Pressure Washer dies when chock rod is put in the

    I just did 2 for the same problem last month for a friend. Take the carb completely apart and remove any rubber/plastic parts. Soak it completely submerged in lacquer thinner for at least 24 hours. Then clean with carb cleaner air and small wires. It worked on both of them. I've found...
  4. F

    Cole Planter

    I purchased a Cole planter at auction. It is orange color. The fertilizer hopper/attachment is missing. Will the fertilizer parts from the green version work on the orange version? Thanks for all replies
  5. F

    needing source for parts for 205 MF

    SO FAR, im needing to find a starter, and a fuel filter for it. Also, does the gas lever pull up out/off of a stem inside under the cover? NEXT, Im needing directions on how to bleed the fuel all the way through the injectors. Thanks ahead of time for any help.
  6. M

    8n loader front mount

    Hello I'm looking for the front axle pin loader mount for a tube frame loader any one make them have a good used one or have good pics of one so I can try to make it myself?
  7. T

    Air cleaner oil

    I?ve been putting the same weight oil in the air cleaners on my tractors as is in the engine. The other day when I was at the John Deere dealer, one of the older guys told me I should put 10w oil in the air cleaner, because it would drip off the screen back down to the cup easier. Is that...
  8. F

    3pt bale spike unroller

    I have a 3 pt bale spike unroller.........the kind the the bale revolves......I have it attached to my 3/4 ton pickup......am trying to decide if a 12 volt hydraulic pump will turn the bale to unroll it......I have a spare pump.......already have one installed for the lifting of the bale up and...
  9. K

    john deere 60 starter spinning but not engaging flywheel

    Hit the pedal and the starter spins every time. It does not however, engage the flywheel. Try it several times and eventually it will engage the flywheel. Anyone have any ideas what I should be looking at? Thanks in advance!
  10. F

    40 years

    I was going through some old pictures a couple days ago. Ran across this one from 1980, which reminded me that later this summer will mark 40 years that I've been driving the Jubilee.
  11. G

    Sediment bowl MF35 gas

    OK guys, I need help. My MF35 hates me, or least the new gas. At least twice a year my Sediment bowl gasket starts leaking. What would anyone suggest for gasket material. Cork seems to work best but what would resolve this issue permanently, I am afraid to empty the sediment bowl for fear I...
  12. M

    Sputtering 2510 gas

    I have a gas 2510 gas PS that we have had since it was a demonstrator. Originally it was our largest tractor now its the smallest but we use it year around.I can count on it starting any time no matter how cold not even plugged in. Once you let it warm up good it works fine a lot of cold oil to...
  13. G

    Pallets and square bales hay

    My friend with horses recently had back surgery and is restricted on what he can lift. He likes to feed with square bales in winter. He buys his hay. I was thinking it might be nice if he would stack and strap hay to pallets and unload them from trailer with his tractor with forks. Has...
  14. F

    Thoughts on a Case 800B with COM trans.

    As a kid on the farm in Northern Michigan we had a Case 800B. We always had problems grinding gears, you sometimes had to hold the clutch in awhile before shifting. Another thing way backing up to hook onto an implement or wagon, you couldn?t release the clutch gently, it was either engaged or...
  15. jon f mn

    Today's Funny

    .
  16. B

    1963 Ford 2000 backfiring and lost all power

    Hey all. First time tractor owner here. I recently bought a 1963 Ford 2000 gas tractor that had a ton of work done by the seller. When I brought it home, I ran all over my property with it, without implements, and it ran great. Then I purchased a 4 foot bush hog and hooked it up. Shortly after...
  17. ptfarmer

    Case International 8312 disk mower/conditioner

    What is the minimum pto power requirement to run a Case International 8312 disk mower/conditioner (rubber rollers). Mainly in grass, or hay grazer on occasion on mostly flat ground.
  18. T

    Injector pump drive gear

    I have a '63 4000 with a 172 diesel. I would like to know if someone could tell me what, the thickness is suppose to be of the shim, that's under the injector pump drive gear. I have searched, and can't find out anything about it. It does not show it, or talk about it, in the parts...
  19. P

    Worn out pin

    I wonder how many hours it took to wear like that.
  20. T

    GCTC Tractor Pull

    By this time next Sunday our first GCTC Pull for 2018, will be in the books. The reason I can say that is its rain or shine, as we open at the Riverbend Arena In Inola, Okla at 10:30 next Sat the 24th.. If you need a place to pull come on down, that's if your tractor fits 2600 thru 7000lbs. This...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top