(800) 853-2651
SHOP NOW

Search results

  1. D

    More 504 problems

    Just got done putting on a Schwartz WF on the 504. Turns hard and squeals standing still on cement floor, when moving or jack up it steers fine. This is the same 504 w/ 3pt. This is the same 504 w/ 3pt and electrical problems.Thank you, DTK
  2. D

    504 Farmall 3pt. Wont raise.

    Hi, 3pt. Hitch on 504 Farmall wont raise unless I move one of the remote levers. It lowers fine but wont raise when I use the 3pt lever. On a separate issue it wont shut off if I turn off key switch or disconnect the neg . Batt. Cable . It has a generator. If I unhook wire off of gen. It will...
  3. D

    504 row crop/Schwartz wide front

    ISO good center steering arm to fit 504 Farmall andSchwartz wide front.This one faces to the rear. 504 has a different bolt pattern than an M and might be thinner. Thanks.DTK
  4. D

    #4 Massey Harris 10 pulltype swather

    Looking for a good canvas for 10 pulltype # 4 swather, also guards and begs. For rollers. Thanks, DTK.
  5. D

    #4 Massey Harris 10 pulltype swather

    Looking for a good canvas for 10 pulltype # 4 Massey swather, also guards and begs. For rollers. Thanks, DTK.
  6. D

    Metro quick hitch

    Looking for parts- latch handles and springs for a Metro quick hitch. Both sides. Thanks DTK.
  7. D

    Farmall 504 worm and sector

    ISO new worm and sector for a 504 row crop. Thanks DTK
  8. D

    504 wide front

    Does anyone have template for the front saddle of a Schwartz WF to fit a 504 row crop bolt pattern? 504 Farmall . Thanks DTK.
  9. D

    # 4 Massey Harris 10' swather

    Hi, still looking for guards and sections and a good canvas for a 10' Massey swather. Thanks DTK.
  10. D

    Schwartz WF on 504 row crop

    Will any Schwartz wf for an H or M etc. fit a 504. The bolt pattern is different, but can you use the same bolster bracket and re-fab it? Are other dimensions different also as in knee/ spindle height etc.? Can you tap the hyd. System to get flow for a two valve loader system w/o using one of...
  11. D

    504 3 pt. Hitch

    What would cause a delay in the lifting of the 3 pt. on the 504 row crop? Dirty filter? The power steering works good. The motor pulls down when you move the remote levers. Thanks,DTK.
  12. D

    #4 Massey Harris 10' swather

    ISO any good parts for a Massey Harris # 4 swather 10', including canvas. Thanks DTK.
  13. D

    986 heater valve

    Hi guys, my 986 is blowing cold air in cab. Both outside valves are open, can see coolant in rad. I have not had the system open , low coolant light off. Could cab valve not be opening ? Do they go bad? This one is the original. It feels the same when I turn it. Any thoughts? Thanks DTK.
  14. D

    Power steering over flow on Super M

    Janicholson and others: If I run the the return from ps unit to the the drain in the factory res. Will it restrict the return too much? Drain is 1/4” pipe thread. 3/8” return line from torque gen. to 1/4” tee in drain hole in res. Thanks DTK.
  15. D

    Flow divider for PS on Super M

    In cold weather my hyd res. Overflows when I start it up . If I close down the flow divider screw it stops but then no PS. It works fine all year but every once in a while it will do this in colder weather. I also have loader on the tractor. Any Ideas? Thanks DTK. Ps I also have an extra1...
  16. D

    Massey -Harris #4 swather

    ISO good canvas for 10’ #4 pull type swather also whatever else you may have for this machine. Thanks . My ph. Is 507- 530-6355 Sw Mn.
  17. D

    IH 82 pull type combine

    Hi , I am trying to fix-up/restore an 82 combine. I could use some help if anyone has had experience w/them and would like to share some info. My email- [email protected],DTK
  18. D

    IH 82 combine

    Hi, I would like info. on an IH 82 combine. The straw rack seems to be traveling to far forward and is hammering out the tin work on the sides. What parts need to be replaced and how difficult? Also any good ideas for removal of gib keys on various shafts? Any help would be appreciated. Thanks...
  19. D

    82 combine year built

    Where is the serial # on an IH 82 combine? Is it stenciled on the hitch? I was trying to find out what year mine was . There is a number on the hitch-2323076R91 this might be a part #. Thanks,DTK
  20. D

    80-82 combine

    Are 80 and 82 combine parts interchangeable?
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top