(800) 853-2651
SHOP NOW

Search results

  1. A

    Massey 180 3 Point Shaking

    Hopefully someone here has some ideas. I have a Massey 180 with Pressure Control. When you pick up a load on the 3 point the tractor shakes. The implement doesn't seem to move up and down visibly but you can feel the entire tractor and implement shaking. It will lift whatever you ask it to...
  2. A

    MF 180 Multi-Power Stops Working

    I recently rebuilt my 180 multi-power system (transmission reworked by dealer (clutch pack, shift valve, input shaft, seals, etc), new auxiliary pump, new multi-power filter, auxiliary pump filter cleaned, oil cooler cleaned and checked for leaks by a local shop) and after about 2-3 hours of...
  3. A

    Massey 180 Won't Move

    I tore my 180 down to rebuild the motor and redo the multi-power. I had the transmission reworked at the dealer so it was just a bolt it back in place deal for me. I got it running today and I cannot get it to move at all. The transmission will go into hi and all gears but will not move...
  4. A

    Massey 180 and 236 Loader

    I am considering getting a Massey 236 loader to go on my 180. I am told that I am looking for a special bracket that moves the loader forward. Does anyone have a picture of a 236 mounted on a 180? Maybe some close ups of the brackets? Also based on a old post on here it moves the loader...
  5. A

    Ford Wheel Weights ID?

    I bought these wheel weights thinking they were the front inner wheel weights for a Ford 1710 but they don't seem to fit that as they would rub the spindles. Bolt holes do line up though so I'm guessing I'm in the right neighborhood of tractors. Any idea what model they fit? They will be for...
  6. A

    Massey 180 Planetary End Play

    I am currently working on a Massey 180 with round axles and am putting new axle seals in as they were leaking and a new outer bearing as it was pitted when I got it opened up. I was reading my service manual and when putting back it says you need a special Massey tool (MF 246Y) to adjust the...
  7. A

    Ford 1710 ROPS

    I bought a set of Hinson Mfg ROPS for a Ford 1710. When I got them they say they are for a 1700 - 1900 from all my measurements they look like they will fit but does anyone have picture of the back axle housing/fenders of a 1700? From the parts book the axles and fenders are different part...
  8. A

    Ford 1710 Remote Valve Mounting and Piping

    Hello All, I have recently purchased a NOS remote valve for my 1985 Ford 1710 w/ position control only. Can someone post several picture of what it looks like on the tractor (a 1910 should be the same as well)? I know where it goes on the side of the case but I am just trying to see how the...
  9. A

    Jerry James Trailers

    Any body know is Jerry James Trailers is still in business in Sikeston, MO? Their website seems down and I tried calling the number on the trailer sticker with no answer. I recently bought one of their deck overs used and need to see if I can get a key for the toolbox.
  10. A

    Ford Tractor Weights

    Hello, Recently purchased these rear wheel weights to go on my Ford 1710. I know these aren't the correct ones for the series but by measurement they fit. My curiosity has got to me though. Anyone know what these actually fit? I looked up the usually suspect similar compact tractors in the Ford...
  11. A

    Ford 1710 Jumpy 3 Point

    I recently acquired a 1985 Ford 1710 compact tractor. This tractor has the single lever system with no draft control. I am trying to use it with my John Deere 272 finish mower. The tractor should be rated to hold this mower just fine but it does not seem to hold position very well. The 3...
  12. A

    WC Magneto shut off rod

    Anybody out there have an extra magneto shut off rod for a WC that they would like to get rid of? Or would anyone know a good person to contact for one? Thanks in advance.
  13. A

    Need some info on this IH plow

    I found the markings for IH and I found a number PO1645 (there could be more because the number was hid by the hitch). I'd like to figure out a model number or something so I can attempt to find a book and parts. There is also a chunk out of the rear moldboard is that suppose to be like that...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top