(800) 853-2651
SHOP NOW

Search results

  1. C

    560 D Oil Cooler

    I have oil dripping from what looks to be the oil cooler area. Can the frame rail be removed without any additional bracing to get to the cooler to replace the gaskets? Thanks!
  2. C

    Power Unit from Combine Engine?

    Did not think of the fuel shutoff either. Thanks!
  3. C

    Power Unit from Combine Engine?

    I did not think of the bell housing. Where could I find one that would work? And where would be the best place to find the clutch?? I priced one from Deere and they were talking close to $2000. Thanks Tj
  4. C

    Power Unit from Combine Engine?

    This is a little off topic but I was wondering what challanges I would have pulling the engine out of a late model 7700 turbo combine and making a power unit out of it to power our irrigation well. I think it is a 404 ci engine. I will need to rig up a radiator, Murphy switches, clutch, and...
  5. C

    560 Axle

    Sounds like a good first step. I will give it a try! Thanks, Tj
  6. C

    560 Axle

    I purchased a 560 Diesel this past fall. It needs some TLC before it goes to the field in the spring. Both axle seals seem to be leaking and I can sometimes hear some poping noise from the right side. I was wondering if the outer bearing can be checked and replaced without pulling the axle...
  7. C

    Manuals

    I purchased an operators manual for my 560D. I was supprised that it did not contain any of the everyday maintainance that needs to be preformed on these things. Is there another manual besides that full service manual that will explain things like adjusting the brakes, clutch, and TA...
  8. C

    New 560 Owner

    Thanks for all the replies. I will change the fuel filters and check into the timing on the injection pump. Sound like a good place to start.
  9. C

    New 560 Owner

    The coolant level looked ok when I got it. I changed the oil and it was not milky, but I will keep an eye on it.
  10. C

    New 560 Owner

    Over the weekend I purchased a 1959 560 Diesel, and have a few questions on it. It seems to blow a lot of white smoke and misses on a cylinder or two after it is started. When I purchased it I figured this would clear up when it got up to operating temp. So when I got it home I changed the...
  11. C

    59 IH 560 Purchase

    Would one off a 450 work also? If I purchase this thing I was thinking about planting with it this next spring and did not know if the one on the fast hitch would work(JD 7000 4 row).
  12. C

    59 IH 560 Purchase

    One more question. Is there a regular drawbar that you can get for these things?? All it had was one that was hooked into the 2 point.
  13. C

    59 IH 560 Purchase

    Thanks for all the suggestions. Yes I was on level ground when I was testing the TA. I will try it again with a load.
  14. C

    59 IH 560 Purchase

    It had good oil pressure, very strait tin, narrow front, two point, and 15.5 38 tires. Just worried about the TA and slight engine miss. tach showed under 3000 hrs and worked but doubt it is correct...
  15. C

    59 IH 560 Purchase

    I am looking at a 1959 560 Diesel. I need a second tractor to go along with my John Deere 720 D. I went and drove it this morning and it seemed to start well. (plugged in 50 deg) Had a few oil leaks around the pan and one injector. Looked like a few drops coming out of the blow by tube. It...
  16. C

    John deere Tach

    I just purchased an early model 7700 combine. The tach does not work. I pull the cable off and it is turning. Are these things rebuildable? Deere wants about $280 for a new one. Thanks TJ
  17. C

    Oil bath air filters - do they get foamy?

    That is exactly how the air filter on my 720D looked when i changed it after it had been running. TJ
  18. C

    slobbering ?? 720D

    As was stated earlier, run that thing up to rated speed. These 2-cylinder engines are not variable speed like the multi-cylinder engines. My 58 720D slobbered when I got it. It had ~5200 hours on it. Found out it was incomplete combustion. We opened it up and the cylinders were pitted...
  19. C

    720 tractor

    I have light silt loam soil and I pull a 4 X 16 plow, and a 13 ft JD BW disk in 4th gear. The 720D is my main tractor. 8) Tj
  20. C

    2 Cylinder Farming

    Mounting a 12 volt battery on the planter was the only thing i could think of. I may look into trying some of the other suggestions. I figured this would work for the monitor for sure but did not know how many amps the electric fert pump would draw. Thanks for all the suggestions!
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top