-
R
Fordson Major Steering Spindle
Old post but for reference, The bronze bushing are to be reamed to 1.5" once installed. An adjustable reamer ain't cheap, $125 bucks! I suppose a brake hone will work may take a while. Just get creative, I wrapped self stick 80 grit around a socket and went to town with an air tool. Heck...- rickne
- Post #1
- Forum: Restoration Processes
-
R
Oil Sump (pan) Need Super Major
Well got the oil pan put on. Used floor jack with transmission adapter and one other person to work the jack. Here is a tip, if you remove and reinstall the timing cover, make sure you do not put to long of a bolt through the front plate on either side!!!!! That little miss hap cost me an... -
R
Oil Sump (pan) Need Super Major
Well the attempt by the welding shop failed. I located a used one, it came and looks fine. I had to shim my radius arm as my old oil pan had a 1" hole to match the radius arm, the new one has a 3/4" hole. No big deal, got a top link bushing and it was a little small so built it up with brass... -
R
D19 Lift Cylinder
Agreed, but around here the shop rates are well, just stupid. I know they have to make a living, but give me a break, $200 est for labor! So I kept hunting for the part numbers and found them though AGCO on line parts catalog. Rockshaft lift cylinder for D19 seal and wiper Seal Assy...- rickne
- Post #1
- Forum: Allis-Chalmers
-
R
Oil Sump (pan) Need Super Major
Thanks Mike, That was my first thought BUT, I really only want to remove and install that beast of a sump one time! The replacement should be here Tuesday and if the weather holds, I will get it back on. It has been like in the 100's here and it is crippeling us northern plains folk! -
R
D19 Lift Cylinder
Having a devil of a time finding a rebuild kit for the [3 point] rear Hydraulic lift cylinder. Any one have any suggestions? Thanks, Rick H...- rickne
- Thread
- Replies: 5
- Forum: Allis-Chalmers
-
R
Oil Sump (pan) Need Super Major
Well found one in Ft Atkinson IA. Under $170 shipped to my door not as bad as I thought it was going to be. Thanks! Rick H... -
R
Oil Sump (pan) Need Super Major
Tracy, Looks like I am going to need a used one. Do you have the serial number of the engine you have handy? Let me know, Rick H... -
R
Oil Sump (pan) Need Super Major
Well it's a bust! Need a used pan. Rick H... -
R
Oil Sump (pan) Need Super Major
I dropped the oil sump by the welding shop I use. He did not see a problem welding it up. He has done many cat dozer pans and engine blocks. My concern is the front seal. That crack goes right through where the seal sits. I should have it back Friday and know if I will be good to go or... -
R
Oil Sump (pan) Need Super Major
It is possible that a Major would fit, depends on the engine serial number. S/N in on flat spot right side above front of injection pump. Thanks, Rick H... -
R
Oil Sump (pan) Need Super Major
Thanks, They are East of Ames. Gonna check local first, that's a 360 mile round trip x2 from me. Rick H... -
R
Oil Sump (pan) Need Super Major
Will stop by welding shop this afternoon. Welding cast is not hard just some very specific steps to take and I do not have the equipment to accomplish it. Must be heated and kept heated while welding. Stick best, I only have wire feed, and wire feed cast wire cost more than the tractor! I... -
R
Oil Sump (pan) Need Super Major
Well I found out why I had oil pouring out the front of the engine, the oil sump is cracked. I have searched here and through Google and can not find a source for either a new one or used one. I suspect a new one would be more than I paid for the tractor! I have sent a request to...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy