(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. N

    engine serial number for farmall location?

    hello i have a farmall m it is either a 51 or 52 and i am in the process of ordering a piston and sleeve kit and i was wondering on the kit they say for engines with serial number over . . . . well what i was wondering was where do i find this serial number i have three motors and they all say...
  2. N

    Farmall H

    i had an m that did that and this my sond dumb but they forgot to put the venturi back in the carb when it was rebuilt, yes it was denies and no he did not stand behind it.
  3. N

    Farmall h hydraulic pump removal

    i have two 'm's and the way i dropped them was with two 16 inch pieces of all thred i removed the front bolt on one side and the back one one the other side and put in the all thred with nuts one bothe of them then snugged up the nuts and removed the last two bolts there is a drive color that...
  4. N

    kill switch for Farmall Super A

    spend the money and get the good switch it seams like every time i use a ruarl king or napa switch i am using a small piec of wire and a screw driver to finish a parade
  5. N

    Hot Coil and voltage

    this happened to me after i did my 12v conversion you will have to take the pulley off of the alternator, go to a shop and get one about o say twice the diameter and put on there that will dial the amperage and voltage back to a usable amount, it really does not take much juice to run one of...
  6. N

    broke a cam gear in a farmall m

    so if i replace the gear on the cam with a new gear the mark on that new gear will be good to use if i reuse my old crank gear and old distributer gaer?
  7. N

    broke a cam gear in a farmall m

  8. N

    broke a cam gear in a farmall m

    hello, i put a live pump on my 51 farmall m, it worked fine till i was going down the road and suddenly the motor spun down with no power as if i had pushed in the kill switch so i did run threw of my check list the motor would turn over it had fuel and power to the coil so i pulled the cap of...
  9. N

    building a stronger motor for a mighty m

    ya im not going to fuel inject a farmall i want around 75 horse power and i can get that with a carb
  10. N

    building a stronger motor for a mighty m

    so here is where my story starts i have an m that has a worn 248 in it and i was at the tractor pull and the worst thing happened to me she powered out!!! the track we pull on has some lime and other stuff in it so the tractors stick very well i had the tires perfect and the weights where...
  11. N

    Farmall M countershaft seal

    i want to know what the I.D. And O.D. and thikness of the tranmition countershaft seal on a farmall m this seal is the one on the transmition side of the pump drive shaft, thanks and i also wonder what the iner and outed diameters of the transmition input shaft are alnog with it"s thikness...
  12. N

    Farmall pulled by horses

    last spring i saw some Amish folks with what looked like an farmall H with no motor or fule tank, just the rear end being pulled by a team of horses but they had a ditcher running on the back of this farmall"s three point that was raised by a hand jack then with this sett up they bailed and...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top