(800) 853-2651
SHOP NOW

Search results

  1. F

    Update super a

    Messed with the tractor tonight and I got it to pop again like it was going to start. And I cleaned all connections and have a better cranking power now. So I put a new tune up kit in last week and I do have power to the points and when you try starting the tractor while looking at the points...
  2. F

    Super a wont start

    Just got done painting a super a and I'm trying to get it to start up and it ran like a clock before it tore it down to paint. So I'm definitely getting spark to all the plugs, new tune up kit, new plugs, new ignition switch. And I'm getting gas because you can smell it and see it on the plugs...
  3. F

    Jd 3300 driving belt

    I need some help on how to change the lower driving belt on a jd 3300 combine. The upper belt has been replaced but the lower on hasn't and needs to be so if I could figure out how to get the belt off I'd appreciate it.
  4. F

    Jd 3300 driving belt

    I need some help on how to change the lower driving belt on a jd 3300 combine. The upper belt has been replaced but the lower on hasn't and needs to be so if I could figure out how to get the belt off I'd appreciate it.
  5. F

    Jd 3300 driving belt

    I need some help on how to change the lower driving belt on a jd 3300 combine. The upper belt has been replaced but the lower on hasn't and needs to be so if I could figure out how to get the belt off I'd appreciate it.
  6. F

    Won't crank over

    Ok working on a Farmall h today and was cranking it over to try and start and the out of know where it decided to stop cranking. Kept trying to hit the starter button but nothing it will not make and noise or movement. I know battery is good and all cables are hooked up. Could it be the ignition...
  7. F

    Paint color

    Would like to know what color paint this is. It's in a 1966 Chevy c60 truck. And will door sill plates from a c10 or c20 work on this truck
  8. F

    1966 chevy c60 paint code

    im getting ready to paint my grandfathers 1966 chevy c60 truck and I need to know to paint code. its like a dark Turquoise or a dark green.
  9. F

    Alternator

    Here's the pictures of the alternator. I need to know we're post A goes I had it running to the "gen" terminal on the regulator is that we're its suppose to go
  10. F

    Alternator wire

    Ok I'm going to try and explain this the best I can so just bear with me. Did some rewiring on the 300 yesterday and had left one wire that goes from the front bolt on the alternator one closed to the distributor I had left it off so I didn't rember where it goes to:/ does it go to the key...
  11. F

    torque

    whats to the correct torque number for a farmall 300 engine head. and also what can you spray on head gaskets so they don't leak around the edges?
  12. F

    farmall 300

    been use the fast hitch a lot the last couple of weeks and been noticing when I pull down on the lever to let the hitch go down it drops it really fast! and it slams what ever is on the back (mostly a bush hog) in to the ground to were im cutting dirt! is there any values that need to adjusted...
  13. F

    No gas

    Did a little disking today with the super m. We'll it got about to run on temp gauge when it started to run rough really rough. So I took off bottom drain plug on carb and there's hardly any gas coming out! Just put all new needle in and adjusted float and flushed out tank as well as cleaning...
  14. F

    Gas problem?

    On my super m I"ve done every think under the sun and still can"t figure out what"s wrong. Ever time I start it up it spits and sputters bad like it"s not getting enough gas. I"ve rebuilt carb and adjust to factory settings many times and still doesn"t run right. Just had to put new coil on it...
  15. F

    Spark plugs

    Recently bought four new champion d16 plugs to put in my super m. The tractor had autolites in it before I changed them. The tractor is running rough at idle and wide open. Do y"all think I need to change plugs or is it a carb problem?
  16. F

    Disk blades

    I have a 8ft ih 37 disc I want to put new blades on the rear gangs. Are the blades 1 1/8? Or bigger. I seen that for the early model disc the biggest size blades were 18 inches. Happy 4th everyone!
  17. F

    140 hydrolic pump

    On my 140 the hydrolic pump started to leak by one of the bolts that mount it to the frame. So took it off found that the hole inside has hair line cracks in it. Bought a used pump from a Super c. I was told it was working when on the tractor. So to make this long story short I put the new...
  18. F

    140 hydraulic pump

    Just put new used hydraulic pump on a Farmall 140 started it up and it wasn"t working but after I put some more oil in and messed with controls it started to work. We"ll it sounds like it gasping for oil and the tubes that go from pump to touch control box are hot so is pump. What"s the problem???
  19. F

    3020 drawbar support

    are 3020 needs a new front drawbar support. just looked on john deere parts and it says they don't make them anymore. I need a new one soon because other one is cracked and welded in spots. so you cant use 3 point arms. any one know where I can get a new or a good used one from. thanks
  20. F

    Timing??

    Alright replaced points condenser and rotor. Rebuilt carb as we"ll.now I"m stumped tractor still sounds the same. My question is could the timing be off? Because it loses power backfires and runs rough when moving.
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top