(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. J

    PTO for MF40 Industrial

    Is it possible to add a PTO to my MF40? If so, what parts could I use?
  2. J

    PTO for MF40 Industrial

    Hi Phill, I am looping back with your PTO setup for your 205 Industrial. How did you go about setting it up with the overrunning clutch?
  3. J

    John Deere 310SG backhoe attachment deminsions

    I found a used rock hammer that has 14" pin holes on center for the bucket attachment. I understand that the JD 310sg has 12" centers. I am curious if the 14" pins would fit? The hammer I am looking at is a OKB 304. The specs for this hammer says it is for a 10k - 16k Carrier rating??? It...
  4. J

    Mf40 front loader hydraulic lever seized.

    Sorry, the loader is a MF34
  5. J

    Mf40 front loader hydraulic lever seized.

    Temperature dropped really fast yesterday to 12 degrees. This is a 71 MF40 with original front loader. The lever in question is the boom lever. The tractor has been sitting outside and was last driven 6 months ago. I have noticed that the boom lever leaks slightly. I have also...
  6. J

    Mf40 front loader hydraulic lever seized.

    I noticed the lever that raises and lowers the bucket has seized. It will not budge even after hitting it lightly with a hammer. How do I fix it?
  7. J

    MF52 Swing Cylinder

    Sorry for the bad quality of picture. The numbers that I can see are PT. No. 708 714 M92 and P.N. 45020????
  8. J

    MF52 Swing Cylinder

    Can someone help me identify my swing cylinder on my MF52 Backhoe. It does not look like a cessna model and I am needing to replace the seals.
  9. J

    MF52 backhoe

    fluid sprays through where the plug is on the cap. When pull any lever and it starts to labor the engine. i am planing on changing the hydraulic filter and replace the fluid. should I have the cap fixed or is it missing a plug?
  10. J

    MF52 backhoe

  11. J

    MF52 backhoe

    I recently acquired a MF52 Backhoe attachment and attached it to my MF40 with a MF34 Fri t loader on it. The swing cylinder is not holding position and is inconsistent with pressure in either direction. I checked the main relief valve and had 1500psi. All the other functions worked well...
  12. J

    Checking MF52 backhoe hydraulic pressure

    I was able to adjust the main relief valve on the front loader that provided pressure to the Front Loader and the Backhoe. It was set at 1500psi, so I increased the pressure to 2500psi based on the instructions in the manual. My Backhoe seems to have poor pressure in the rotary cylinder and...
  13. J

    Checking MF52 backhoe hydraulic pressure

    I would think so also. The service manual says that the backhoe pressure is serviced from the loader control valve. I understand how to check the main relief valve by forcing the lift cylinders to each stroke extreme. Would I force the boom cylinder to both stroke extremes to test the...
  14. J

    Checking MF52 backhoe hydraulic pressure

    I recently installed a MF52 backhoe to my MF34 Front loader on my MF40 Industrial. I want to make sure the backhoe is getting adequate hydraulic pressure. Do I perform this pressure test from the control valve test port on the front loader or somewhere on the backhoe? If from the front...
  15. J

    MF34 Front Loader Filter

    I am wanting to inspect the hydraulic oil filter on my MF34 front loader. I am curious how much hydraulic fluid should I expect to lose if I inspect the filter iif the fluid current level is full?
  16. J

    MF34 Loader Dip Stick Missing

    Yes, I have the Agcoparts book as a resource. Trying to find a replacement or make one.
  17. J

    MF34 Loader Control valve hose removal procedure

    Ah, that makes sense. Thank you!
  18. J

    MF34 Loader Dip Stick Missing

    I found a old post in the forum giving the measurements of the dip stick for the MF34 loader. The post stated that the dipstick was 11 3/4" from the bottom of the breather housing to the full mark. 13 3/4" from the bottom of the breather housing to the "add or low" mark. I am curious what...
  19. J

    MF34 Loader Control valve hose removal procedure

    I needed to remove a hose on that port that was connected to a cylinder on my 3 point hitch. I was attaching a backhoe pressure line, so I simply installed the backhoe pressure line to that port and now the backhoe works. I was not sure if that hose removal procedure is only when you are...
  20. J

    MF34 Loader Control valve hose removal procedure

    What tool is needed to remove the 1/2" pipe plug on the loader control valve as indicated "1" in picture. Also, what is the purpose of the procedure if the hose is removed from the loader control valve, then that port is to be plugged, remove the 1/2" pipe plug, then reinstall the 1/2" pipe plug?
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top