(800) 853-2651
SHOP NOW

Search results

  1. C

    4020 with 466 turbo motor

    This question is for Tim S. Tim did you ever build more of the wedges to lay the water manifold over for the turbo clearance??
  2. C

    1967 4020 diesel blowby

    I just bought a nice original 1967 4020 diesel and wanted to run it on the dyno to find leaks and check the horsepower. I checked the engine oil, hyd. oil and coolant before I let the tractor warm up good on a light steady pull on the dyno. Once warmed up I started pulling the tractor down to...
  3. C

    Grandparents 4430

    Well here's the final restoration pictures of my father and I's 4430 all done and the hood back on. I also included one before picture from 2017 when the tractor was found and brought back home.
  4. C

    Grandparents 4430

    Just updating the progress that's been made the last few months on painting my 4430.
  5. C

    Grandparents 4430

    Still working on the 4430 getting things ready for paint and primer as I write this. I can't wait to finally have this tractor all done.
  6. C

    Grandparents 4430

    I posted sometime awhile back about finding my grandparents 4430 and all the work I have done to it. I went through the quad range transmission this spring replacing all the bearings, B range and D range gears, all the forks, shift cams, top shaft friction disk and reverse gear collar among a...
  7. C

    4430 camshaft

    I had posted back a few months ago about finding my grandparents 4430 I was just updating that I finally got around to replacing the camshaft which I'm sure was original. I think I was on borrowed time because there were some teeth flaking off on the old one it wouldn't have run much longer. I...
  8. C

    Grandparents 4430

    I'm a long time follower of this website just haven't posted before. I had asked a question about a 4430 camshaft yesterday and decided I should share my story on this 4430 that my grandparents had purchased new in the spring of 1973. They used this 4430 as the big tractor for many years on...
  9. C

    4440 camshaft

    I am working my early 4430 tractor and it needs a new camshaft and oil pump gear. My question is I have a friend with a brand new never used cam out of a 4440 I can buy but I see they are different part numbers the 4430 is a AR100385 and the 4440 is a AR100386 I was wondering what the difference...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top