-
0
Power Steering Pump Leak
Morn'n All, My pump has a small leak from the cap on the side. I cant seem to find an exploded vied of the pump. Is this simply replacing the cap o ring or is there a deeper issue? Is there a part number or size available if it is just an o ring? Thanks!! -
0
Exhaust Manifold Leak/Repair On A 51
Years ago when I bought my N the exhaust manifold had been leaking and was eroded from the exhaust gas. I removed and cleaned up the manifold, built up the low area with a braising rod, trued up the surface with a belt sander, doubled up exhaust gaskets using high temp RTV and reinstalled. My...- 00_Green
- Thread
- Replies: 9
- Forum: Ford 9N, 2N & 8N
-
0
8N Wheel Bearing & Seal Part Numbers
Does anyone by chance have the generic part numbers for the front wheel bearings and seal? I took mine apart to clean and grease, one of my inners is toast. I hope replacements are available at the local auto parts store. Thanks!- 00_Green
- Thread
- Replies: 5
- Forum: Ford 9N, 2N & 8N
-
0
Started running Rough
My 51 had been running good. After a short break I restarted it and it was running rough. Pulling the choke definitely smoothed it out. I'm leaning towards a fowled carb but wanted to ask for suggestions incase I'm over looking the obvious. I did pull the plugs as it's been a while and they all...- 00_Green
- Thread
- Replies: 4
- Forum: Ford 9N, 2N & 8N
-
0
New to me 641 - Electrical System Question
I recently purchased a 1959 641 that has seen better days. I've cleaned the carb, was able to unstick the clutch, and I'm ready to tackle the electrical system. The tractor had been sitting so I charged the battery and it cranks and runs but is not charging. What I know is that a 12v battery is... -
0
3400 Clutch Replacement Question
I have an older 3400 diesel that I've split for a clutch replacement. The flywheel has been resurfaced and I have a new pressure plate and clutch disc. The original pressure plate was sitting on spacers/shims. Are the shims a required part of the installation or optional if needed to adjust... -
0
3400 Clutch Questions
Hey Gents, I have an older diesel 3400 and have have a few clutch related questions. 1. There's a grease cup on the bell housing you turn and it forces lube to where? What grease should be in it? How much and how often does one turn it? 2. If I pull the steering box is there a cutout in...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy