(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. P

    Got massey fergusion 65 injector pump in leaking at shut off is this hatd to fix

    No remove top cover just an o ring around fuel shut off shaft raise cover slightly and look under before you disconnect spring put back together using the same holes
  2. P

    Got massey fergusion 65 injector pump in leaking at shut off is this hatd to fix

  3. P

    Super A Oil Pressure

    I guess I might as well give up on this site I can’t get anything to show up where I tried to put it anymore and it’s constantly jumping around everywhere. I know I am at fault but tired of trying
  4. P

    Super A Oil Pressure

    If the plastiguage shows .010 that’s your problem. Should be .001 to .003
  5. P

    Super A Oil Pressure

    If the plastiguage shows .010 that’s your problem. Should be .001 to .003
  6. P

    Looks like YT is kaput

    I don’t know why i posted what Jim me said earlier. I must have done it accidentally. I wasn’t trying to post anything.
  7. P

    Looks like YT is kaput

  8. P

    Looks like YT is kaput

    Might be mine too
  9. P

    I'm out of the loop

    Where’s classic view
  10. P

    Harbor freight or tractor supply wire welder

    I have a Hobart that the wife got me for Christmas several years ago. It is a 120 volt. I forgot the model and I had never used a wire feed welder before. Been using stick welders for over 50 years. This one only has one knob for different thickness metal and it seems to run the wire out faster...
  11. P

    Marine Battery vs Reg Battery

    Which ever type battery you use be sure to recharge it after it is used each time. If it is left sitting under charged it will sulfate and loose capacity. A low amp charger maintainer (1 amp or close) should do fine.
  12. P

    Geo th jube

    I think the cure for the Jube with sticking valves would be instead of starting it up often for a few minutes is to let it run twenty minutes or more when it is started. If run to operating temp plus several minutes more whenever it is started the condensation problem will go away. Make sure the...
  13. P

    Buyer/Sellers - How to You Advertise on FB Marketplace??

    I thing the is it available gets hit accidentally a lot of times. I am left handed and usually scroll with my right thumb. I get yes its available sometimes when I never asked if its available to my knowledge. They need to put the button some other place.
  14. P

    67 IH Farmal gas 656 coolant in oil pan & shifter st

    I wouldnt run it more than 5 seconds with no coolant. The cylinder walls will get super hot with just air behind them. Put straight water in to run it for a test. I have ran them without coolant for a couple minutes but not any more after one locked up. You can run the engine with no radiator or...
  15. P

    Belarus tractor voltage ??

    I have a 560 m that is12 volt
  16. P

    Interesting comparison test of penetrating oils

    On small things I have used many different brands with mixed results. On large things I have found water to work good if it stays wet for a few days. The guy with the stuck receiver hitch if he can remove the entire hitch from the truck and throw it in the pond for a week then tap on it with a...
  17. P

    Cheap ignition

    I have done it on a 360 dodge and a 302 Ford that were originally electronic ignition but only used the hei module and a separate coil. One coil was from a 4 cylinder s10 the other was from a Ford TFI . They worked good. The reason I did it was I had plenty of the hei modules and the China dura...
  18. P

    2006 Pontiac Grand Prix

    Make sure the Pcv system is working properly. Not just the valve. Make sure engine is coming up to temp and not just short runs. Good thermostat?
  19. P

    Leaking B radiator

    You can use stop again alumna seal or bars leaks original with the pellets. Or you can find which tube is leaking and snip it off at the top and bottom tanks and solder the slots in the tanks. Trying to solder the tube itself has not worked for me. Jb weld might work on the actual hole in the...
  20. P

    4230 Temp problem

    Radiator cap or overfilling
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top