(800) 853-2651
SHOP NOW

Search results

  1. zuhnc

    Engine blocks over the years

    Did Ford ever NOT put a sleeve into any block they manufactured for any of the N-series? I.e, no sleeve and 0.040" oversize pistons from the factory? Can the same be said about any Ford industrial engine that may have been put into any N-series? I.e, not originally built for the N-tractors.
  2. zuhnc

    6V, 3 Brush generator no output

    I have what I am is assuming is this: 9N-10000-A generator from a 1948 8N. A FLD and GND terminal on the side near the back, ARM terminal on the back, and the external third brush adjustment screw on the back. I do not know the history of the tractor. It had a 2-unit regulator attached (BAT...
  3. zuhnc

    Newly acquired 1948 8N

    New to me 8N. Particulars: Serial *8N66692 (no * or diamond after number). Front mount distributor. Six-blade fan. Generator (unknown model) on right side. Long oil fill tube front left on block. Date codes on various parts - Left Trumpet-C35, Right Trumpet-3-18-48. Differential...
  4. zuhnc

    Bob takes a swim

    Mowing around my pond, and Bob feels he has been worked too hard today. Midway through the process of persuading him to get out of the pool. One thing I did NOT remember to do, prior to starting the persuasion, is putting his transmission in neutral. Once I remembered to do that, he was less...
  5. zuhnc

    ''51 8N 3-point won''t operate

    I recently went through the hydraulics on my 8N; new piston, cylinder, guide pin, repaired the quadrant, disassembled, cleaned and reassembled the pump (nothing worn), etc. Adjusted per specifications, and installed proper lubricant. The hydraulics worked properly for a period of time. Now...
  6. zuhnc

    1951 8N hydraulic pump valve guide pins

    1951 8N. Removed hydraulic pump for repairs and inspection. Replaced only pressure relief valve; other parts good, valves not worn, no pitting, etc. The question is: should the guide pins for the valves be loose, or lightly trapped between the bottom of the bore and the cap? I measured...
  7. zuhnc

    8N lift arm bushing issues

    I had mentioned in another thread about rebuilding the top cover of my 1951 8N. I ordered lift arms, gaskets, cylinder, etc., from a well known vendor. Included in that order were two lift arm bushings, stated in the catalog to be 2" ID, 2-3/8" OD and 3" long. The bushings I received were...
  8. zuhnc

    1951 8N-C, serial 378716 - external air pre-filter

    New to the forum as I acquired this tractor when I bought the 40-acre horse farm in Macks Creek, MO, recently. 1951 8N-C, Serial 378716. This tractor is equipped with an external cylcone-type air pre-filter. It appears to be original equipment. Bolts to the right side of the hood in place of...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top