(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. H

    Restoring steering wheel

    Thanks for all the advise. I'm shipping it out Monday to Evergreen Restoration. Hayes49
  2. H

    Restoring steering wheel

    Send me a email on contact info. Wheel is off of tractor, that's not a issue. Just wanted to keep the same wheel that my father, grandfather and great grandfather used. Thanks for response
  3. H

    Restoring steering wheel

    Have a 8n steering wheel that needs rubber redone. Has anyone ever tried using the rubber dip or anything else for that matter. Replacing the wheel is not one of my options. Tractor has been here since 49. All advice appreciated. Thanks
  4. H

    Steering box after 216988

    Have steering box on bench reassembled but something isn't right. When steering gets to the middle where wheels would be straight steering wants to tighten up and bind. Once past the middle right or left it's free with no binding. When I originally tried adjusting it I went by the different...
  5. H

    Steering gear sector shim

    Thanks JB...after reading F0-4 for what seems the 100th time I seen where it called for a specific tolerance on it and specified it being like the first pik. Thanks again.
  6. H

    Steering gear sector shim

    I've taken tons of piks on disassemble but I missed this one and I'm sure more. Which way does shim/washer go on sector shaft of steering. 1st pik on the head of adjuster or 2nd pik between sector and steering gear side cover. 49 8n after 216988. Thanks once again for the help. Hayes49
  7. H

    8n generator advise

    Bruce AMI had it and shipped it out today. Thanks again for the help!!!!
  8. H

    8n generator advise

    JF, I'm in NW Florida. Bruce, I'll be calling them this morning.
  9. H

    8n generator advise

    I'm restoring my Great Grandfather's 49 8N and took the starter and generator to my local electric motor shop to have them service and clean both internally. Starter is fine. Generator is not. Armature is burnt out. Shop hasn't been able to find one and I checked with YT, Just 8n's, Fix that...
  10. H

    Steering shaft

    Wore Out thanks for the info. Figured out the question concerning bearing. It should be fine because bearing sits on worm just like it does on the bottom. Thanks again.
  11. H

    Steering shaft

    When I disassemble steering column all the bearings were in pieces except for lower bearing in housing. I have parts now to begin reassemble. First question is the ring on shaft. Is this supposed to be there or is it a part of the upper bearing that rusted in place due to neglect or is it a seat...
  12. H

    4630 PTO seal leaking

    Yell I'm not sure if I resolved anything with cleaning the vents out other than it needed doing. There was minor oil and trash in the one when I stuck a piece of wire in it and I think it was able to vent. Not sure. Going to pull the shaft out tomorrow and take with me to dealership to let them...
  13. H

    4630 PTO seal leaking

    Other side
  14. H

    4630 PTO seal leaking

    ...Okay I have actually two of these bolts. Never new anything about them. One was fairly clean the other was stopped up. Cleaned out both and reinstalled. Top bolt doesn't have vent maybe due to you'd have to remove seat to remove it. Only vent I ever knew about was at gearshift fill plug...
  15. H

    4630 PTO seal leaking

    I have a Ford 4630 that's had the PTO seal replaced 3 different times over about 15 years with each time the same results. Leak does not go away completely. Instead it turns into a real slow seep which gets worse over time till its back leaking. One time I even had a retired mechanic who had...
  16. H

    PTO seal leaking badly

    I give up on video.
  17. H

    PTO seal leaking badly

    Try again
  18. H

    PTO seal leaking badly

    Try this again
  19. H

    PTO seal leaking badly

    I know I'm off forum model #'s and I apologize for that but there's a lot of Guru's on here with some wise years of knowledge. I have a Ford 4630 that's had the PTO seal replaced 3 different times over about 15 years with each time the same results. Leak does not stop. One time I even had a...
  20. H

    1949 8n Red paint color???

    Thanks....Showcrop
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top