(800) 853-2651
SHOP NOW

Search results

  1. M

    injection nozzle design

    why is it that almost every diesel engine old enough to be mechanical injection uses nozzles with a leakoff manifold/lines but the d282 has none? i always thought it strange to have leakoff- after all, isn't the injection pump supposed to meter the fuel, so i'd think it should all get burnt...
  2. M

    JD 780 hydra-push manure spreader

    I'm trying to rehabilitate a 780 spreader, and the two pieces of angle iron with the square holes, W38365, are completely rusted out. does anyone know 1) what are the actual dimensions of the new part and 2) what exactly is their function? to hold the sliding floor up or down? or something else...
  3. M

    Taters

    Are all planted. Here's how we do it.
  4. M

    Dave from MN- 806 brakes

    Hey Dave did you ever figure out why your 806 was locking up the brakes?
  5. M

    JD 6620 value

    Hi all, I drove by a scrap yard the other day and saw a 6620 sitting out front. got what looks like a 213 header on it (tinwork with the number was missing). Asked about it, turns out the PO drove it there. Called him up, he says there's some stress cracks in the seive/chaffer, hyd oil leak-...
  6. M

    IH gassers no premium gas? thoughts on previous post

    Just thinking about Tractor Vet's response to the post below re: can't get 93 octane any more and just brainstorming. What would happen if: 1. put an undersized piston or oversized sleeve so it has room to expand without seizing? is it possible without getting into blowby issues? 2. what about...
  7. M

    224t knotter problems

    Hi all, any advice on this would be great. My problem is just with the left knotter: during the tying cycle, as the intermittent knotter gear engages the twine disk pinion, the knotter is pushed away from the intermittent knotter gear and the twine disk pinion jumps a tooth. of course, then the...
  8. M

    super c hyd valves

    Hi all, I am working on adding 2 aftermarket hydraulic valves to my super c: one to operate the fast hitch, and one for a remote cylinder. I"ve got the non-fast hitch type of steel hyd lines and the bypass block, and a pair of gresen valves. Now I just need to find a sturdy and comfortable place...
  9. M

    404 life span?

    What is the consensus- how many hours would you expect to get out of a turboed, intercooled 404 engine before overhaul? The 4630 is our primary tillage tractor, got almost 5800 hours. It looks like the injection pump and main bearings might be headed down hill. Local mechanic said they are only...
  10. M

    806 front end threads

    the threads in the lower 2 holes in the front bolster have been stripped, probably from years of use with front mounted IH cultivator (it bolts on to connect). Anyone have any good ideas, other than a whole new bolster, for repairing the threads to be strong enough to hold a bracket with 1000#...
  11. M

    NLA disk harrow parts

    Hi all, I need 2 bearing supports for the inside front bearings on an IH 370 disk. these are the ones with 2 bends that add up to a right angle. NLA from dealer, any idea where I could find some? I've got the old ones, but they have been bent, racked, and twisted so's not to fit up to the...
  12. M

    farmall 806 front axle

    am in the process of replacing the pivot pin bushings on the front axle. I&T book says they should be reamed after installation if necessary. I'd say it's necessary since the pivot pin won't fit through the new bushings. got myself a 1.245" reamer and gave it a try. expected it would self-center...
  13. M

    806 front axle

    am in the process of replacing the pivot pin bushings on the front axle. I&T book says they should be reamed after installation if necessary. I'd say it's necessary since the pivot pin won't fit through the new bushings. got myself a 1.245" reamer and gave it a try. expected it would self-center...
  14. M

    JD 224T baler

    Just got a new to me 224T. greased it up and tried it out by feeding loose straw into the pickup by hand. seems to tie well, but about 1/2 the time will break the twine right near the knot. It's a frayed break, not a clean one, and it's mostly on the right side. I'm still using the twine that...
  15. M

    986 steering hand pump leak

    Had a pretty fast drip from the steering pump. Replaced the "rotor seal" p/n 537279r1 (the big black rubber band) and that seemed to fix it for about a year. took a look again today and it's leaking again, looks like the same source. double checked the bolts holding the pump together, still...
  16. M

    JD 224 baler transporting

    Going to pick up a 224 baler this weekend. Anyone know the approx weight of that beast? I'm told the overall width is 8'1". The trailer deck is 7'. Is there enough wiggle room to cock the baler at an angle to get both tires on the deck and keep the chute at the back within legal width? Or is the...
  17. M

    white 7300 hydraulic pump drive

    Have a 7300 diesel. The hydraulic pump is driven via v-belt from the front (timing gear end) of engine. This has been a problem spot ever since we've had the combine- the belt just isn't tough enough, so it slips, wears, breaks, etc. In the parts manual, I see a drive hub for direct mounting to...
  18. M

    harvesting corn

    the situation: about 16 acres of field corn. 1/2 is grown for duck hunters who want it harvested a little at a time during the hunting season. top yield isn't a major concern. we use all the corn on farm- mostly fed to pigs. the equipment: -plenty of tractors -can borrow a neighbor's new idea...
  19. M

    ChrisLSD- Oliver 7300

    Hey Chris- do you still have that Oliver 7300? If so, I'd be interested in the hydraulic valves. possibly a few other parts. I'm trying to get our white 7300 functional again. thanks Nathan email is open
  20. M

    blue ribbon service manuals- which one do I need?

    The tractor at issue is a '64 F806D with the RD injection pump. I want to get the corresponding service manuals for the engine/fuel system. I've seen GSS-1345 "Fuel System Diesel Engine Model D-361" as well as GSS-1345-B "Fuel System Model RD injection pump engine model D-361." Do I want one of...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top