(800) 853-2651
SHOP NOW

Search results

  1. C

    Farmall 300 Hydraulic Valve

    I know the topic has been discussed before but did not see an answer to my specific question. I changed orings between the valves which helped with fluid leaks, I did not change the small oring on the valve shafts so I still have leaks. Now to my question. Must the valve be completely...
  2. C

    Other make hubs/rims for Massey Harris 22

    My Massey Harris 22 has 11.2 x 34 inch rear tires. They are cracked and coming apart. Since 11.2 x 34 are almost non existent and very expensive. I am trying to find a different solution. Could be different brand hub/rim that would allow 36 inch like my super c farmall or a hub/rim swap from...
  3. C

    Massey Harris 44 Radiator

    My mh44 radiator was not repairable, leaking deep in the core. I ordered and installed an aftermarket radiator, the lower water inlet does not line up with the motor inlet. Their is only about an inch between the two, no way to attach a hose. The top inlet lines up good. The radiator shop said...
  4. C

    Massey Harris 44

    I am faced with a leaking radiator around the lower hose inlet. Also have a seep around one fin where it goes into top tank. Looking inside at the fins that can be seen some are plugged with rust. All of these issues can be fixed for a price which approaches the price of a new radiation. I...
  5. C

    1948 Model A

    My A is leaking transmission oil from the cover behind the flywheel. Looks to be a oblong match stick rust hole. I need to confirm the cover should not have a hole to let oil pass from a bad deal.
  6. C

    Farmall 300 rear hydraulic line

    Like many have noted I have a leaky rear hydraulic line on my 300. It has been blazed several times, new holes appear over time. I read where some have replaced with hydraulic hose. How do you attach the hose to the valve. Is it threaded or do you cut the line and keep the block that attaches...
  7. C

    MH 44 PTO shaft

    MH44 has a slight wobble in PTO shaft (bent). I have a replacement, but before changing would like to find out how involved the change out will be. I'm not sure how you get the splines to line up. Does the trans cover need to come off? All advice is appreciated.
  8. C

    1947 John Deere A starts again

    Finally got the A to start. Replaced points still no go. Replaced cap and coil. Why? Both were most likely original to tractor. The coil had spark but not a good blue color. After talking to the mail order house tech. , I learned the old cap had been updated to a two post version, my old cap...
  9. C

    1947 John Deere model A still will not start

    I posted a few days ago about a non starting John Deere A that has an xh1042 magneto. I was getting an intermittent spark at that time so I installed points and condenser along with a new rotor. The old rotor had a broken clip. Right after installing the points the spark was jumping the plug...
  10. C

    1948 John Deere A xh1042 mag will not start

    John Deere A equipped with XH1042 mag will not start. It can be pulled started but puts out black smoke for a period before starting to run. It does not have much power and will usually die within a couple of minutes. So far I have filed the points, they are nice and shiny with only a very...
  11. C

    MH 22 pto oil seal

    I have the new seal and a service manual that does not explain how to change the seal. I can tell the four bolts in the bearing cap must be removed. It appears the entire shaft comes out and you remove a large snap ring to separate the cap from the shaft. What happens on the coupling end...
  12. C

    Massey Harris 22 PTO Seal Number

    Does anyone have a pto seal number for a Massey Harris 22?
  13. C

    MH22 transmission mainshaft oil seal

    My MH22 is leaking grease where the driveshaft enters the transmission. Does anyone know the oil seal number? The shaft has quite a bit of side to side movement. Any way to tighten the bearing? What is the bearing number? I picked up from this site that the jam nut has left hand treads and the...
  14. C

    MH44 cracked frame

    My MH44 tub was cracked and welded several years back. I noticed recently a new crack has developed next to the old weld. The new crack is slightly over an inch long. The crack is where the tub meets the transmission under the shifter rail. Their is enough material between the crack and...
  15. C

    Starting 3020 diesel that has set 5 years

    Need info. / tips of items to check before attempting to start a 3020 diesel that has been setting for about 5 years. My experience is with gas tractors. Items I need help with are, what needs to happen to diesel in tank?, will the injectors need service?, will the injector pump need service...
  16. C

    International 87 planter

    I'm having a time finding a manual for a International model 87 planter era 1970's. This is a four row 3 point planter. It was setup to plant sweetcorn when I got it. Works good. It came with more plates I'm trying to find the correct plate/ setting to plant blackeye peas. If anyone has a...
  17. C

    Massey Harris mounted cylinder

    Posted before with no reply so I'm reposting. Does massey harris models 22,33, & 44 use the same mounted hydraulic cylinder? I'm looking for a replacement and need to know if the 22 & 33 will work on a 44.
  18. C

    Massey Harris 44 Hydraulic cylinder

    Looking for replacement cylinder. Does the 33 use the same cylinder? I had the one I have rebuilt, still will not hold weight for over a few seconds. Could be the spool valve.
  19. C

    Farmall 300 yoke style keyed u-joint

    My steering u-joint needs to be replaced. The current u-joint has a welded yoke on the shaft the steering wheel is attached to, with a keyed collar on the end that attached to the shaft going to the steering bolster. Looks like my choices are to find the u-joint cross and renew the existing...
  20. C

    1947 JD A rough running at open throttle

    My 1947 A is running rough with the throttle open. At low to mid range it seems to run good. I tried pulling a plow and found the tractor lacks power and is exhausting black smoke with the throttle open, it also pops back through the oil bath air cleaner. This tractor ran great until today...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top