(800) 853-2651
SHOP NOW

Search results

  1. M

    d 14 transmission removal

    hello--trying remove transmission-axle assys off,& pto. pulled all bolts from trans to power director-unit will slip back, almost disengage p-d shift fork, will come no more. does fork & cross shaft have to be removed, & clutch unit come out with trans? thanks for help
  2. M

    installing perkins sleeve

    hello all--this weekend i plan to install a sleeve a flange type sleeve in 336 perkins. i have build a fixture to press it in. i plan to use 640 sleeve retainer, pack sleeve in plastic bag with dry ice. question came up about cold messing with loctite. did this years ago, but it was less press...
  3. M

    sleeve retaining compound

    helping installing sleeves in mf 135 diesel engine. notice #3 is gonna be light on press fit. i ran into this once before, & used a 'loc tite' type product, can't recall what it was. what do you folks use?
  4. M

    2'' dash amp gauge

    hello all--does a standard 2'' 60 0 60 dash mount amp gauge care if its 12 or 24v [except for backlight}? was researching vdo brand, shows some require shunt for 24v. however parts store shows same brand as 12/24 in description. sounds like either?
  5. M

    OT--pt cruiser door decal.

    well, I backed into wife's car-damaged driver door. [ouch] found one, same paint color. I wish to transfer the vin decal from original. possible? any tips? thanks.
  6. M

    855 cummins injector tube

    Hello all--While installing fuel injectors in 855 cummins engine, I found one with bottom o-ring burnt, & metal eroded away. so, injector became unseated, or tube cracked/ damaged--see nothing with naked eye] ok, I believe this tube hold back coolant? ( did a 7.3, but it put fuel in coolant] can...
  7. M

    ceramic magnet repair in 12v motor.

    hello all. I have a small 12v motor, the glue that holds the permanent magnet to the case has come loose, anyone made a repair like this? looks like it was baked on, of course, was wondering about JB weld or ??
  8. M

    attn-Dieseltech--[re, lucas pump timing]

    Many thanks for pointing me in the right direction on the lucas pump. pulling pump off today, take to pump shop. you are right-on all the way. the case/cummins I had done, had this same pin/oblong plate, it would engage--lock @ proper spot. I first thought pump had been repaired, using wrong...
  9. M

    lucas injector pump timing help

    OK, I am working on ford 555E 4 cyl.--(taking over assembly where someone else left it)-yeah, I know)---Injector pump was removed for minor seal job on top cover-That parts good---installer before me marked the shaft & gear, said he maybe put it back-same spot. torqued the nut. he said pump...
  10. M

    OT-f-600 brake adjuster

    Hello--on a 1984 ford-600 rear brakes,[hydraulic] can anyone tell me how to back them off? they are self-adjuster starwheels, & has the parking spring brake that is released by its own 'power steering' type pump. there must be a tab or something that rides on that star wheel. but darn if I can...
  11. M

    d14 rear axle shaft

    Hello--I'm working on an allis-chalmers D14, need to pull the rear axle shaft to replace seal, check bearings. I have pulled the center bolt-& shim pack, tapped on axle flange without getting too rough] moves a bit & stops. I don't have manual for this tractor, but parts diagram shows snap ring...
  12. M

    david brown 990 stuck pto clutch

    Hello all--need info on this clutch set-up, believe it is the borg&beck 2-stage. so far, I have adjusted the 3 small set screws on pressure plate--[turn cw to stop, back out 2 rds,] info found in archives]. the main clutch works great,& can feel 2nd stage, PTO will not release. I blocked the P...
  13. M

    another delco 10si question

    I read the post a couple of days ago about placement of 'sense' wire. I loop it back to output post on alt. the diagram that shows that wire running all the way to battery looks best, especially if bat. is farther away. Then I wonder about the same alt. that is converted to 1-wire. Is that...
  14. M

    checking in-

    I had a good day------
  15. M

    ford 4r100 transmission tss problem: round #2-help!

    Ok, a couple of weeks ago, I posted about shifting problems, flashing OD light, code po715--Turbine[input] shaft sensor signal. a couple of YTers posted back, thanks. Here is whats going on. I have scantool hooked up & it shows 0 rpm @ tss. I replaced sensor, no help. Truck will drive & seems to...
  16. M

    OT-4R100 transmission problem

    Hello all--hoping for some help on my 2001 super duty trans. OD lite flashing, code po715-'turbine shaft input speed' scantool shows erratic movement til a few mph, than drops 0 speed. yeah, that's gotta be sensor, I thought--wrong. new one same thing. gears all seem to be there, just shifts...
  17. M

    convert 301 powertrain to reverser

    hello all--I have a JD 302-A tractor w/reverser. also can get a 301 parts tractor [no reverser]with bad motor. The 302A has been worked hard as a loader tractor, and its got some real serious ''pop'' clanks'' when you change directons & general gear noise, no brakes. the donor tractor has nice...
  18. M

    ford 3000 pto shaft

    well, working on this pto that wouldn't go in gear. pulled shaft & find broken/missing snap ring in bearing retainer. -seen that before--pull shaft out & find centering pin on input end had broken off. broke off in shaft!--haven't seen that before---ouch! Where to start split?
  19. M

    used up all my shear bolts today.

    hooked up 5 ft. rotary cutter today, used up my stock of 3 shear bolts & not done yet! first was high grass- stopped for gear change, got off clutch too fast, too much rpm. second, junk rubber, third was sand rock where it wasn't suppose to be. [It is known fact that rocks grow feet in winter &...
  20. M

    allis chalmers 7060 a/c

    Does anyone know the amount of 134a it takes to fill this system? all original cab air, except for 134a fittings. I know about pressures, temp, deduct for 134a, just looking for simple original factory baseline.
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top