2630 John Deere water coolant pump rebuild

Whoa! Page 2 here. Thanks!

Back from the dealer to return the shortie tube.

Things are looking up! No problem with the pump housing gasket since they had the right one in stock and it even was a hamburger's price cheaper than other one I had from them. They even had the seal and driver in stock--John Deere and their inventory has them as separate parts, but the kit--both together with a kit part number-- they don't have that and that fooled me last time there. Ha.

I now have everything I need to reassemble the pump, the top tube off eBay has been shipped and from the length measurement they gave me, looks to be the correct length.
 
Last edited:
Whoa! Page 2 here. Thanks!

Back from the dealer to return the shortie tube.

Things are looking up! No problem with the pump housing gasket since they had the right one in stock and it even was a hamburger's price cheaper than other one I had from them. They even had the seal and driver in stock--John Deere and their inventory has them as separate parts, but the kit--both together with a kit part number-- they don't have that and that fooled me last time there. Ha.

I now have everything I need to reassemble the pump, the top tube off eBay has been shipped and from the length measurement they gave me, looks to be the correct length.
How about posting the part numbers for the individual seal and driver parts you got and the kit number they are in, it might save someone hunting time, in the future.
 
Here is my parts list, all from John Deere. Thanks for helping me compile it.

Included is the short piece of coolant hose which goes into a metal tube headed toward the oil cooler. I found mine to be hard like a rock so it should be replaced, it is expensive. The long metal tube attaching to that was corroded underneath the hose ends, but it was salvageable after cleaning. Also in that circuit is the nipple pressed into the water pump housing--mine had corrosion where the hose inserted over it, but deemed viable after removal of the rust and scale with sandpaper. I sprayed some primer on it.

I don't know if that press-in nipple is available as a separate part, but I think it would be the devil to remove it. That's one of those things which should be evaluated before DIY rebuilding, which might tilt one toward a rebuilt, or new, pump.

I also included the gasket for the lower thermostat housing where that bolts onto the block--note that this gasket has a different part number than the gasket of similar shape at the thermostat itself. I reused the impeller.

Part numbers for 2630 John Deere early water/coolant pump rebuild:

Gasket, back plate-to-block: T20243
Gasket, pump housing-to-back plate: R55405
Bearing assembly, KOYO: JD9257
Seal, spring-loaded half: AR97882
Seal pressing tool, required for above: R518805
Seal, ceramic washer: R32174
Seal, rubber retainer for ceramic washer above: R40243
Tube/bypass insert, early engine serial, 2.4" long: R54809
O-rings (two needed) for tube bores in pump and thermostat housing: R56461
Hose, small, short, angled, water pump nipple-to-tube toward oil cooler: R48766 (sub. for U42685).

Thermostat: AR48675
Gasket, between upper and lower thermostat housing: T20215


*If one has the later engine serial, then two short tube/bypass were used instead of the one long tube for the early engine. The two "shortie" tubes need a section of hose between them fastened with hose clamps. If not rebuilding the pump, buying an aftermarket or rebuilt pump instead, the tube already included in the pump could be the short tube, so one additional short tube is needed, the one inserting into the lower thermostat housing. However, if using the pump for the early engine serial, I would guess that a short tube insert would need to be removed for the long tube's use, instead. Here are the parts needed for that, as follows:

Tube/bypass insert, two needed, later engine, 1.34" long, stepped diameters of 1.110"/1.125" : R59050
Hose between above inserts: R59052
Pipe clamps, two needed: ___________

The fiber-rubber gaskets are branded "Interface Performance Materials N-8092, made in USA". They are 1.0 mm thick. The spring-loaded seal is indicated on the package as also being a domestic part and the ink jetted numbers on the seal are "261513" and "11:25" . The packaging for the plastic seal tool indicates a domestic part. The packaging for the thermostat indicates it is a domestic part, as well. The bearing assembly is KOYO, made in Japan.
 
Last edited:
Hi again folks.

The bypass tube R54809 arrived today. It is a plain steel pipe with no varying diameter. If ordered from John Deere, the cost is 70$. The measurements on it are 2.380" long, 1.125" diameter, 0.065" wall thickness. Looking around on the internet, I see tubing with an OD of 1.125" (1-1/8") is a standard tubing size.

After removing the short coolant hose on the nipple coming off the right side of the pump, I found a fair amount of rust on the nipple. The nipple is a press fit into the housing and I wish I had checked it and removed it before painting the housing.

The nipple has not perforated, but it does seem from experience, that pit rust which has penetrated steel is quite hard to stop. Even after cleaning the rust-off and treating it, thinking it would be ok to reuse, doubt crept in, and I decided to order that nipple from John Deere. It is a press-in tube and has a stop step machined into it, part number is:

R34985 Water Pump Tube.

I am aware the old nipple it might be hard to remove, but after watching a few Youtube videos of folks showing tricks for removing hose nipples from water pumps of various old cars, etc., I think I can twist it out without catastropie, the key strategy commonly proposed being to insert something close to the nipple I.D. and twisting out the nipple with vice grips or pipe wrench, the insert being used to keep the tube from collapsing under the twist. Heat is also suggested by some.

Looks like I put this old pump on in 1989 as a rebuilt from John Deere, so it is 37 years old. I don't remember doing it, it has been that long ago.

One minor correction to my previous post (which I am no longer allowed to edit), is that the two-hole fiber rubber gaskets for the thermostat housings are manufacture's gasket type N-8091, not N-8092, just in case someone wants to cut these from sheet.

I'll also mention that I bought an aftermarket pulley hub to replace the one I broke. Looks about the same except it is not quite the same length--shorter. Glad I checked this! According the the manual, my JD pulley is to be pressed on until flush with the end of the shaft, but due to the shorter length of this one, I'll have to press it on a little past the end of the shaft to compensate.
 
Last edited:
The short hose barb nipple off the pump's right side, R34985, arrived today and I am going to post the dimensions in case someone needs to make one:

The inserted end is 0.725" in OD diameter, tapering up to 0.750" OD at the hose barb. It seems most likely that the tube was all one diameter but that the process which makes the hose barb ring expanded the metal OD to either side of the rise.

The diameter around the barb itself is 0.825".

Wall thickness is 0.065", which is noticably thicker than the nipple I removed. The overall length is about the same as the old nipple, 1.715". Insertion depth into the housing bore, taken from marks on the old nipple, is around 0.60". I should be able to simply tap the new nipple in, I think. Looks like plain steel, magnetic.

Because the insertion depth into the housing is not much, the old tube came out easier than expected, twisting with the help of a mini-pipe wrench, adding some heat to the inside of the tube from an oxy-acet torch, and inserting a close-fit plug into the tube to keep the tube from collapsing during the twisting.

Once I could twist the tube, I added some penetrant and twisted on it more for about a minute, then I re-heated, switched to some vice-grips and resumed twisting back and forth but now with a pulling force added to get the tube out.

On the bypass tube I mentioned in the previous post, R54809, I just noticed a burr in one end's chamfer. I'll smooth that off so it does not cut the o-ring during insertion.
 
Last edited:
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top