Late Styled B Vertical Steering shaft Removal

AndrewG

Member
Before I set up and tackle this, do some of you have experiences and advice for removing the vertical steering sector shaft? I have a late styled B with the rollamatic and have posted previously about some of the things I've found. I now know that this stuff has been swapped from some other production of tractor, but I know to actually see what I have I'm going to have to remove the whole thing. I have read of many people supporting the front of the tractor and then rotating the pedestal/front end to remove it from the side rather than trying to 1. Raise the front enough to pull it out 2. Fully remove the whole front section due to weight.

If any of you have removed that much, I'd appreciate some pointers. I am either going to have that shaft machined down at the top to fit the eccentric bushing that is correct or if I'm going to search for another shaft. I will probably go with the machining option simply due to it appears there have been other modifications that could become a problem if I try to go back 100% original.

Long story short, the eccentric bushing has been removed and the shaft replaced with one larger than the original. This means there is a lot of slack between the worm gear and sector gear. It will contact properly for a little bit, but then the least imperfection on the ground causes movement and the wheels just dart wherever they want to so it is absolutely unsafe to drive.
 
@Loosehandle I absolutely may do that. I would still kinda like to hear some experiences with removing this stuff and ideas. How far would the front have to be lifted to remove or if it is safer/better to rotate that front end and remove sideways. Due to the size, I'd like to find one kinda close by here in North Alabama.
 
If you left the pedestal attached, wheels off, you would need to lift the tractor five feet plus to get the steering shaft dropped out. I don't think you can rotate the pedestal, because there are studs screwed into the pedestal to hold it on. How would you get all studs out but one to rotate? We would take out the top steering rod and take off the whole pedestal. We used a wood crib under the front of the tractor, raised up to to support? Loosehandle suggest tractor salvage yard, good idea!
 
@JIM MN thank for that. This is exactly why I posted this here. I had read somewhere that someone did the rotation but just as you described I didn’t think it would work based on the studs I saw as well. I’m scanning the salvage options but need to get deep enough to see what someone has swapped and what would still work. I know an old machinist had it and there are signs that the steering shaft (wheel to work gear) has been cut down from an other tractor and welded to make it the correct length. The vertical shaft is certainly larger than should be for a B in my production range but don’t know if the pulled/modified one from an A or some later other model. I’ll post updates when o disassemble the lower part and get some casting numbers. I bought a 2nd tractor for parts but it ended up a little nicer than the first so rather than rob parts, I’ll just make 2
 
Search Youtube for Humble acres. The young man there salvaged a Late A from his granfather, and he had to do just what you are doing. Here is the link to his reassembly
--you can go from there to look for the disassembly. Anyway, it shows what he did--very little by way of extraordinary effort. It will be easier on your B as it is smaller and lighter.
 
I would also go find exactly what you want in a junkyard and I would use a lifting device of some sort even if it is just a harbor freight cherry picker to pick up the front end crib it and then safely remove the front down to the ground no sense in getting hurt

Not that it really matters but one thing that might fill in the puzzle a bit is what casting number is stamped in the sector gear?
 
Search Youtube for Humble acres. The young man there salvaged a Late A from his granfather, and he had to do just what you are doing. Here is the link to his reassembly
--you can go from there to look for the disassembly. Anyway, it shows what he did--very little by way of extraordinary effort. It will be easier on your B as it is smaller and lighter.
@Steven Allen thank you for the video. This is exactly what I wanted to see, and what I’ll be doing sometime in the near future.
 
I would also go find exactly what you want in a junkyard and I would use a lifting device of some sort even if it is just a harbor freight cherry picker to pick up the front end crib it and then safely remove the front down to the ground no sense in getting hurt

Not that it really matters but one thing that might fill in the puzzle a bit is what casting number is stamped in the sector gear?
@Fixingfarmer Thanks. I’ll pull that sector gear again and see what it says. Like others have said that’s good advice to try to see what really is in this old tractor. The more I see pictures and watch these videos it is more obvious that is is not originally from the B. If I had to guess the old farmer/machinist modified one from an A to put in it.
 
@Fixingfarmer Thanks. I’ll pull that sector gear again and see what it says. Like others have said that’s good advice to try to see what really is in this old tractor. The more I see pictures and watch these videos it is more obvious that is is not originally from the B. If I had to guess the old farmer/machinist modified one from an A to put in it.
At least you could figure out what it is it might help someone else if they need something or if they have the right shaft
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top