Dogsix

Member
Does anyone know how I can Identify what kind of PTO I have on my 73 gas 1020? The service manual states I can have one of 3 different PTO setups. When engaged, My PTO shaft turns continuously regardless of clutch pedal position. When disengaged it stops. Is it a dragging clutch that needs adjusted or is it continuous hydraulic drive?
 
Did you just get this 1020? It looks like you past posts were about a Ford NAA.

Is the lever to engage your PTO located between the shift levers? Does it keep turning if the clutch pedal is fully depressed and held? If so, it is an independent PTO.

What is the full serial number of your 1020? Do you have the correct Operator's Manual for it? There were two North American ones and a German 1020 based on serial number. Using the PTO types is explained in the Operator's manual.
 
Serial # tag explanation for 1020 built for sales in N America is shown in photo below. Nothing is mentioned in SN tag explanation concerning type of pto. If this tractor has hyd IPTO it will have a control handle shown in 2nd photo between gearshift levers. If no control lever then it will either have continuous running AKA dual stage clutch or transmission driven pto. One option is if dual stage clutch or trans driven if the pto clutch is stuck causing pto to operate when engine is operating & pto lever on LH side of trans is in forward position. I've never personally seen a JD 1020 that I knew had a trans driven pto & I was employed at JD dealer from '65-'87.
 

Attachments

  • Screenshot 2026-11-18 044657.png
    Screenshot 2026-11-18 044657.png
    79.3 KB · Views: 0
  • Screenshot 2026-11-18 045517.png
    Screenshot 2026-11-18 045517.png
    131.9 KB · Views: 0
Serial # tag explanation for 1020 built for sales in N America is shown in photo below. Nothing is mentioned in SN tag explanation concerning type of pto. If this tractor has hyd IPTO it will have a control handle shown in 2nd photo between gearshift levers. If no control lever then it will either have continuous running AKA dual stage clutch or transmission driven pto. One option is if dual stage clutch or trans driven if the pto clutch is stuck causing pto to operate when engine is operating & pto lever on LH side of trans is in forward position. I've never personally seen a JD 1020 that I knew had a trans driven pto & I was employed at JD dealer from '65-'87.
The only reason I asked the serial number was to determine the year. It appears the early ones did not offer the independent PTO, not tha the serial number actually called out the PTO type. And to direct him to the correct Operator's Manual if he doesn't have one.
 
Did you just get this 1020? It looks like you past posts were about a Ford NAA.

Is the lever to engage your PTO located between the shift levers? Does it keep turning if the clutch pedal is fully depressed and held? If so, it is an independent PTO.

What is the full serial number of your 1020? Do you have the correct Operator's Manual for it? There were two North American ones and a German 1020 based on serial number. Using the PTO types is explained in the Operator's manual.
Yes I just aquired the 1020. I still have the NAA and she’s going strong.

The 1020 serial number is: T4R1C 169860T

I’m pretty sure I have the correct manual for it as I have been studying it while fixing other issues and it coincides well.

The lever to engage the PTO is located down low on the left side of the transmission housing.
When the lever is engaged the PTO runs all the time regardless of what I do with the clutch.
The manual says if the PTO turns with the clutch fully depressed it could be that the clutch just needs adjustment.
My question is do I need to adjust the clutch or is this normal for this tractor PTO.
 
I agree as you previously stated your 1020 is a '73 model. My guess is pto clutch is stuck. In lieu of attempting to adjust pressure plate I suggest to acquire a post hole digger then carefully with clutch pedal fully depressed, engine operating at idle speed dig some holes hoping that if clutch is stuck to PP it will free up.
 
If it was single stage (aka Transmission PTO) when you fully depress the clutch pedal when traveling, and the tractor stops, the PTO would stop as there is only one clutch disc.

The two-stage (dual) clutch has two discs the travel disc against the flywheel and the PTO disc inside the pressure plate. Pushing the clutch pedal about halfway down disengages the travel disc to stop the tractor but keep the PTO operating. Pushing the clutch pedal the rest of the way down disengages the PTO disc to stop the PTO. You say pushing the clutch pedal all the way down does not stop the PTO, that indicates a stuck PTO disc with a two-stage clutch. (You do not have the small lever between the gear shift levers, is that correct?)

Tx Jim is giving you a way to see if the PTO disc inside the pressure plate is stuck and possibly free it if it is stuck.

The Operator's manual is different than the service manual. It has maintenance info for the services and maintenance normally done by owners and operators, where the service manual has repairs and overhauls in it and not as much basic maintenance. John Deere publication OMR48388 is the Operator's manual for your 1020 I believe.
 
No I don’t have anything between the shift levers.
I will try your idea with the posthole digger and see what happens. I believe I have a service manual but I will send pics of them to confirm they are correct
The tractor has one of these two clutches correct?
So am I correct to assume it has a two stage clutch? With a stuck disc on the second stage disc?
Sure thank you for your help!
 

Attachments

  • image.jpg
    image.jpg
    2 MB · Views: 0
  • image.jpg
    image.jpg
    2.2 MB · Views: 0
Yes, you have a service manual.

If the PTO is still turning when the clutch pedal is pushed as far as it can go, I would say you have the dual stage clutch. Give Tx Jim's post hole digger idea a try.

I marked up your picture to show the PTO disc and shaft.
 
Will try that as soon as I get a new line installed on it for the hydraulic pump bleed line to the reservoir. It may take me a few days.
Thanks again
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top