(800) 853-2651
SHOP NOW

Recent content by 101SU

Yesterday's Tractor Forums
  1. 1

    Cockshutt 40 frontend

    Will a narrow frontend off a 30 bolt up to a 40? The 40 currently has a homemade wide front and would like to install a narrow instead. If not where can I find a 40 narrow?
  2. 1

    head swap

    If it does fit you will have very weak compression and may not run unless you install the wc flat top pistons. Im not a big allis man but I think the WD45/D-17 heads are flat with dished pistons the wc is opposite.
  3. 1

    Where can I pull this.

    It started as a 1950ish Lehr Big Boy all original except for the frontend has the 230 chrysler.
  4. 1

    Paint numbers for a Lehr

    Anyone know where I could buy paint for a Lehr Big Boy or possibly a code? All pictures I look at have the wheels painted red but I also read wheels painted grey. Also are there any decals out there?
  5. 1

    Where can I pull this.

    Looking for classes for this tractor. 3000-4500lbs open RPM. Any one still pull these old tractors? Im located in southern indiana.
  6. 1

    wheel bolts

    I saw some the other night at.http://www.millertire.com/
  7. 1

    Massey 101 front rim

    I have the 6 hole wavy hubs on my 101 and the rims are rusted out. Anyone have luck using trailer hubs and rims on a 101?
  8. 1

    Need new 101 senior rims

    I need to find new front rims for my 101 senior they are rusted out. Its the 6 hole wavy hub. Has anyone had luck using a 5 hole trailer hub and rim? I might add this is also a pulling tractor and any weight I can save would be helpful. Thanks
  9. 1

    chry 8

    I have two tractors with straight 8 chryslers. I was going to put a 8 in my 101 but no where to pull it. I did the measuring and it would fit. The 8 doesnt have near the rpms as a 6. The torque and hp on a 265 and 323 are not far apart. Plus its hard to find parts for the 8.
  10. 1

    Engine installation Problems

    I was installing a new engine this weekend and ran into a problem. The input shaft from the tranny has a 2 inch pilot before the splines the new engine crankshaft does not have clearance for the pilot. Should I drill clearance into the crank or could I cut off the pilot and be fine?
  11. 1

    Chrysler Straight eight

    Bud Its a 324 cubic inch 8cyl out of a dragline. Not the orginal motor it had a 230. Custom had some 8cyl from factory and Lehr and custom are almost identical. I also have a Wards with the straight 8.
  12. 1

    Chrysler Straight eight

    I have a electric fuel pump the old pump gave out awhile back. This is on a lehr tractor.
  13. 1

    Chrysler Straight eight

    Does anyone know where I can find a water pump for a chrysler 324 cubic inch? Mine has a bad wobble and leaks out the front.
  14. 1

    Wards Brakes

    Where can I get brake liners for these dodge rearends? Need some for a Lehr also. NAPA?
  15. 1

    101 super

    Are you wanting to pull? I have a chrysler 230 bored over .080 I might consider selling. This would be a direct bolt in for your 201. It is set up for open RPM, NO Gov has headers, hei dist, and GM downdraft carb. Email me if interested located in southern IN.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top