(800) 853-2651
SHOP NOW

Recent content by 1175case

Yesterday's Tractor Forums
  1. 1

    1175 hyd controls

    1370 rod wondering if you or someone on here knows where the lever in the valve can be found? Dealer says obsolete part? Thanks!
  2. 1

    1175 hyd controls

    Have a late model 1175 think it's a 77' anyway one of the hyd control remotes is stripped out leaving only one remote. Seems to be a small machined piece that the lever hooks to inside the hyd block, wondering if there is a easier way to fix this than removing the block and replacing with a...
  3. 1

    Adding a pto to a Jd h

    Would like to add a pto to a 41h have a donor tractor with all the parts to swap, question is how much of a job is this and what if anything on the inside do I need? Thanks
  4. 1

    New idea 323 picker plugging

    Have a new idea 323 that can't seem to get adjusted right and always seems to plug up and drag the stalks with it. Have tried adjusting rolls in/out come to the conclusion there's got to be something wore out? Can't see anything obvious but don't really know what to look for. Thanks for the help!
  5. 1

    Omc 590 roll baler ground speed

    Hi, have a 590 roll baler and just wondering if anyone out there has experience with them? My big question is what ground speed should I be able to bale at? Currently seems like if I go over about 3mph I get plugged up? Wondering if the gearing could have been slowed down on the pickup or if...
  6. 1

    1175 hydraulic/pto disengage issue

    Went out and ran it for about an hr on the disc, seemed to purge some air out. Adjusted cable now it holds all the way thru the rpm range but over 1500 if you shut it off does not want to disengage until you throttle it back to about 1400 maybe that's just normal operation? And maybe it would if...
  7. 1

    1175 hydraulic/pto disengage issue

    How tite does that need to be? Should I be able to run it manually with the bracket removed? Or does it need more pressure on it? Just seems erratic like there's something in the flow divider valve
  8. 1

    1175 hydraulic/pto disengage issue

    1175 case original issue was pto would not stop. Removed housing and replaced cluch pack brake pad is good. Reassembled and op checked still not shutting off. Disconnected cable and I can make it stop sometimes/ sometimes it won't, also varies with rpm will hold at idle but most times will...
  9. 1

    Ford jubilee/ naa lack of power

    Ford jubilee has lack of power, can barely pull a 6ft back blade or 6ft finish mower. Ran a compression check and got these results from front to back 125/120/115/115 dry then added oil to cylinder same front to back 180/175/200/200 thinking compression isn't perfect but should not cause this...
  10. 1

    1175 pto cluch disassembly

    Problem is pto cluch will not stop, removed housing from rear of tractor, book says remove 2 snap rings I removed the large 1 and small pin and fitting the hyd line connects to. Do not see how to get the small snap ring off because it seems to Be recessed in the shaft? Anyone whose done it...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top