(800) 853-2651
SHOP NOW

Recent content by 1949H

Yesterday's Tractor Forums
  1. 1

    C152 boring and stroking

    Good Morning All, I purchased a W4 and as part of the deal a spare engine came with it. I took apart this spare engine and didn't find anything obviously wrong with it. My plan has been to pull the sleeves and bore out the block about 0.062 to 3.625. (I mentioned this in the Farmall forum a...
  2. 1

    Farmall C152 engine boring question

    Thanks all for responding and giving different options to look into. I have found some cases where people have used pistons from different tractors and cars even after they have bored out their engines. However these pistons MUST have different compression heights (height from the top of the...
  3. 1

    Question for 1949H or others

    Fritz, I have not looked into the measurements of the quill stroke vs the depth of the bore so I do not know if it would reach the bottom of the bore in 1 stroke. If the quill does not have enough stroke to reach the bottom of the bore I will raise the knee to reach the bottom (after measuring...
  4. 1

    Farmall C152 engine boring question

    Hello everyone, I have a C152 block out of my W4 that I would like to bore out to run the C175 (3.625) pistons. I have read a bunch of different articles online about those who have done this but they don't seem to get into any detail about how they did it. So I have a couple questions: 1-...
  5. 1

    Help needed to identify AC tow behind brush cutter

    Thank you all! I feel like I made out pretty well after reading the responses!
  6. 1

    Help needed to identify AC tow behind brush cutter

    I'll put the photos in this time.... haha
  7. 1

    Help needed to identify AC tow behind brush cutter

    Good Morning Everyone, I was lucky enough to pick up this tow behind brush cutter over the weekend from a guy a few towns over. It's a 6 foot cut with pneumatic tires on the rear. It appears to be in really good shape and she's built like a tank!! The gear box does seem to be leaking so I'd like...
  8. G

    Implement wheel speed ratings

    I have the hardee tilt trailer. The wheels on it are rusted out. I was gonna put new implement wheels but everything I find is only rated for 25mph. Why are the rims only rated for 25mph. I was going put radial trailer tires on it and pull it down the road and use it for long trips. I am...
  9. C

    New Holland baker wagon hitch

    I am going to try and build my own wagon hitch for my bc5050 baler. Just nothing around my area for parts and it doesn't seem that it will be too difficult. I could use some dimensions though. How long is the hitch from the end of the bale chamber and how far below ( if up from the ground)...
  10. 1

    1950 McCormick W4 live hydraulic setup

    Hello, I recently got a 1950 W4 and the she runs like a top! I would like to get her setup with live hydraulics using a pump off a 300,350 or super H. I am told the front plate needs to changed as well. What about the front plate is different between the W4's c152 and the newer, upgraded...
  11. 1

    Mccormick W4 Buyers Guide ?

    Hello, I just purchased a 1950 W4 and would like to switch from 6v pos ground to 12v neg ground before anything else. Do you have a magneto or a distributor? What size tow behind brush hog do you run? Id like to get a mower for the W4 to held with fall mowing.
  12. N

    6700 no power

    My 6700 tractor doesnt have good power it lugs down going down the highway pulling a balewagon I was going to check the pump timing it has the big piston pump simms not the little cav pump the book is not clear on it what degrees should it be on It has 5600 hours on it and do I check it with...
  13. F

    annual spring sale in Dorchester - update

    Silo unloader repairs took priority this morning, so I didn't get there until a little after 1:00. The Fords were already sold, so I didn't get to hear what they brought. Didn't see the 2000, but the 8600 and 8970 looked real nice. ...especially that 8970. The TW 35 that was added after I...
  14. H

    two spool valve

    631 ford has one spool valve under the seat, would like to mount two spool hyd valve is it possiable to remove the one spool valve and mount the two spool under the seat, if not where would be a good place to mount the two spool other then fender
  15. super99

    Too Wet to V Rip??

    I have about 2 acres of wet areas that I try to v rip in the fall to help the water get away. I have an old 9 shank V ripper that I bought and cut down to 5 shanks and then I take 2 off so it is 3 shanks. I pull it just as deep as I can get it into the ground behind my 1850. I tried it this late...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top