(800) 853-2651
SHOP NOW

Recent content by 1961casepuller

Yesterday's Tractor Forums
  1. 1

    Pulling with a Case DC

    I have a 49 dc that weighs 3700 with a 190 pound driver in the seat.
  2. 1

    30 series gas heads

    Anyone out there got a set of 30?s series gas heads I?m needing 3 of them or even a set of 70?s series gas heads thanks
  3. 1

    Vac final drive gear needed

    I am searching for two 67 tooth final drive gears and the pinion gears that matches the final drive gears if anyone out there has a set I would like to purchase them please let me know what you?ve got my email is open
  4. 1

    310 rear end and transmission

    I can?t slow my vac ratio down so I?m considering changing my 201 engine out of the vac to a 310 tractor rear end and transmission to get myself a better selection of gears sorry for the confusion
  5. 1

    310 rear end and transmission

    Anyone out there close to East Tennessee got a rear end and transmission out of a 310 case they would part with? Thanks
  6. 1

    Vac ratio help needed

    Hello all I?m needing som I for on the different gear ratios on different model vac?s. Did any of them have a faster or slower ratio and if they did have a different ratio was it changed in the transmission or the ring and pinion I?m wanting to slow my vac down and all help is greatly...
  7. 1

    Dc clutch question

    I have a 49 dc that has a hand clutch and I know that they made some later models with a foot clutch. My question is can I convert my hand clutch tractor to a foot clutch or is it more complicated than just swapping parts? All your help is much appreciated
  8. 1

    What happened Big Tee

    I watched your 500 run strong all weekend at white pine and was extremely impressed with it but I saw you trying to roll start it Saturday night after your last run and it was just sliding the wheels. What do you think happened to it? Hopefully it?s nothing to major
  9. 1

    Ready for reassembly

    We decked the top of the block and shaved the head and installed a set of new set of high compression pistons in it the truck is a 37 Plymouth sitting on an s10 frame its still a working progress
  10. 1

    Ready for reassembly

    Well I?ve been working diligently on getting my dc pulling tractor back out on the track and figured while I was at it I would freshen the heartbeat of the ole girl up. So after a little changing internally she?s finally ready to go back together
  11. 1

    Dc hitch redesign

    I?ve still got to weld a plate in above the drawbar then I?m going to drill a one inch hole in that plate and the bottom plate to weld two nuts over then I will screw a grade 8 bolt from the top and bottom to lock the drawbar in place. We are allowed 20 inches from the ground to the hitch point
  12. 1

    Dc hitch redesign

    No I built it on the bench beside it
  13. 1

    Dc hitch redesign

    Been redesigning the hitch on my DC for a while now and about to get finished up with it. I kinda got side tracked working on my vac puller and put this one on the back burner but now that the vac is finally finished it?s time to pull out the big horses and put this ole girl back on the track
  14. 1

    Vac brake trouble

    I have replaced the seals in my 49 vac brake housing 3 times in the past 2 years and I still continue to get oil in my brake housing from the rear end. I don?t feel any play in the bearings supporting the shafts coming out of the housing so I?m stumped as to why I cant get these seals to hold...
  15. 1

    Looking for a pulling sled

    Any idea of what they will possibly want for the sled and scales?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top