(800) 853-2651
SHOP NOW

Recent content by 20BlackburnJa

Yesterday's Tractor Forums
  1. 2

    Difference between John Deere M and MT attachments

    Hello, iv got myself in an interesting predicament. I have an MT that use to be my grandpa's and I have the front blade a one bottom plow for it. Iv bought and sold different MT plows over the last few years but recently iv acquired the disc and a factory chisel plow that appears to be for only...
  2. 2

    1940 John Deere D advice on rebuild reassembly.

    Well I managed to get it in. I used a bolt half the diameter of the hole and put it through the hole in the shift fork and used channel locks to press the bolt down and compressed the ball and spring. Was then able to start the shaft and hold tension on it and the bevel on the end held the ball...
  3. 2

    1940 John Deere D advice on rebuild reassembly.

    Hello, I got another interesting question on my D. Have you ever put a pto on one? Thats what im working on right now. Im trying to get the shaft put in for the shift for and there is a little spring and detent ball inside the shift for that locks into notches on the pivot shaft. I cant for the...
  4. 2

    1940 John Deere D advice on rebuild reassembly.

    Im definitely going to have to check the clutch. I pulled it at a pull 2 falls ago and about the 250 foot mark the clutch started to really slip. It pulled a plow just fine but slipped on the sled so im hopeing it just needs tightened some. Thanks for the help!-Jacob
  5. 2

    1940 John Deere D advice on rebuild reassembly.

    Thanks for the reply Bob. The IT manual came in today and I was suprised about how much they have in it referring to D's. The parts book is how iv gotten this far just by looking at the breakdowns, and surprisingly a decent amount of those oart numbers are still good. Got the operators book out...
  6. 2

    1940 John Deere D advice on rebuild reassembly.

    Hello, Im currently trying to bring a styled 1940 John Deere D with hand start back to life. It had a cracked block, head, and lower radiator tank. I currently have it down to the crank case and waiting for the rest of the parts to come in. Im not pulling the crank but I am going to reseal it...
  7. 2

    John deere 50 pto adjustment

    Thanks for all your guys help. Dynoed it this evening and it still slipped so brought it home and popped it apart real quick. Ill post so.e pictures of the carnage but I dont think there was any adjusting that was gonna fix this. Ordering a rebuild kit tonight and hopefully it goes back together...
  8. 2

    John deere 50 pto adjustment

    Thanks for the reply! Iv been able to release the locking tab, this one doesn't have a screw, and I can spin the cam but I cant see a gap anywhere to measure, the book just shows sticking the wire through but cant tell which surfaces you stick it between. Could I get away with adjusting it 3...
  9. 2

    John deere 50 pto adjustment

    Helloi was wondering if anyone has any experience or advice for adjusting the pto clutch on a john deere 50? It slipped a couple times last fall on a ear picker and skipped again on the dyno at our local fair and I was told I should try adjusting it before I rebuild it. Im trying to get it ready...
  10. 2

    John Deere D carburetor

    I'll be getting in touch!
  11. 2

    John Deere D carburetor

    Thank you! Glad I'm not the only one lol. I was told they put a new carb on and just couldn't get it adjusted right. It'd help if it was the right one lol. I'll send that fellow an email now.
  12. 2

    John Deere D carburetor

    Hello, I have a couple questions about carburetors on John Deere D's. Me and a buddy purchased a 1940 styled D over the summer and have battled carburetor issues since we've had it. A guy at our local show mentioned it had the wrong carb on it, one from an earlier unstyled since it's all brass...
  13. 2

    John Deere 60 belt pulley/clutch assembly reinstallation.

    I think I found it. Tore it all back down and the clutch bearing is lose and wiggles all around. The bearing mount did not hold. Now I am assuming the outer race is suppose to be tight in that housing? Tried sending a video but it yot angry at me lol. Again thanks for all of ur guys help.
  14. 2

    John Deere 60 belt pulley/clutch assembly reinstallation.

    I have the clutch disc pulled out if it at this point and it still does it. It's like nails on a chalk board but it's not constant, it's every half second or so. About like a high pitch chatter. Even though the bushing slipped on with the assembly you think it might be too tight? I have to tear...
  15. 2

    John Deere 60 belt pulley/clutch assembly reinstallation.

    Well I thought I had everything ironed out, but there is still a screeching comeing from the clutch assembly, I adjusted the clutch and everything where there is a crisp pop to engage the clutch. The belt pulley does not have a lot of up and down play like it had before. But it still screeches...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top