-
2
1855 oliver field stock build
they do it to every tractor before the season starts and then they will do it again if a tractor is being protested- 2150
- Post #6
- Forum: Oliver, Cletrac, Co-op and Cockshutt
-
2
1855 oliver field stock build
They bottom out a piston and pull the injector and pump fluid in. Then they have a formula that tells how bigger it is by how much fluid was pumped in- 2150
- Post #4
- Forum: Oliver, Cletrac, Co-op and Cockshutt
-
2
1855 oliver field stock build
Looking into the IPAs new field stock class. Pretty simple rules 426 cu limit 2500RPM limit P7100 limit they supply a s362 box turbo that you are not aloud to alter must be stock block and head for make and model. Stock intake and exhaust manifolds. No intercooler allowed. And no de-cubing...- 2150
- Thread
- Replies: 5
- Forum: Oliver, Cletrac, Co-op and Cockshutt
-
2
1855 oliver field stock
Looking into the IPAs new field stock class. Pretty simple rules 426 cu limit 2500RPM limit P7100 limit they supply a s362 box turbo that you are not aloud to alter must be stock block and head for make and model. Stock intake and exhaust manifolds. No intercooler allowed. And no de-cubing...- 2150
- Thread
- Replies: 4
- Forum: Tractor Pulling
-
2
Hope this is the right place
Hey thanks for the reply! I ain't real good with the internet so I take that stuff with a grain of salt. I have seen a few 3208s make some impressive hp I am just worried with these restrictions in either club I won't be able to get enough air for to make it with my while. My family has been die...- 2150
- Post #3
- Forum: Tractor Pulling
-
2
Hope this is the right place
How much horsepower can you get out of a 3208 cat with a 2.75 inlet charger Apump and 2800 rpms? Those are the rough rules for a local open speed class Also how much hp can you get out of a 478 herc? rules call for 2800rpm max across the bored and turbocharger with a 2.330" inducer bore...- 2150
- Thread
- Replies: 6
- Forum: Tractor Pulling
-
2
What to build
How much horsepower can you get out of a 3208 cat with a 2.75 inlet charger Apump and 2800 rpms? Those are the rough rules for a local open speed class Also how much hp can you get out of a 478 herc? rules call for 2800rpm max across the bored and turbocharger with a 2.330" inducer bore...- 2150
- Thread
- Replies: 3
- Forum: Tractor & Farm Talk
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy